Cree Edge Series - User Manual

1 of 2
CI321X01R0_B
THE EDGE
®
LED Security Wall Mount
Includes: SEC-EDG-WM
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
TO INSTALL:
WALL MOUNTING
STEP 1:
IMPORTANT – If needed, the (2) Keyhole knockouts located
inside box may be removed, but are for alignment only. See
Figure 2. Luminaire is to be supported by (4) 3/16” mounting
holes. The Mounting holes will accommodate a #10 bolt.
Select appropriate customer supplied mounting hardware for
mounting surface. See Figure 2 and 5.
STEP 2:
Place mounting box over junction box or conduit. If mounting
over junction box a 2-1/2” Inspection knockout hole is
included. See Figure 2 and 5.
NOTE: See Figure 4 for minimum mounting box distance to
achieve a required 3" clearance.
STEP 3:
For surface wiring (4) 1/2” threaded holes are available. See
Figure 2 and 5.
STEP 4:
If mounting on a uneven surface, place a minimum of a 1/4”
bead of high grade silicone on the black gasket encompassing
the Inspection Knockout hole on the back of the mounting box.
See Figure 5.
STEP 5:
If mounting over surface mounted conduit use the knockout
conduit openings located on the top, bottom, or sides of the
luminaire. Knockouts can be removed by using a hammer or
pliers. See Figure 3.
STEP 6:
Before securing to wall mounting surface, make sure
mounting box is level.
STEP 7:
Secure mounting box to wall.
STEP 8:
For ease of installation, hook the (2) installation support cable
loops on the top screws of the mounting box.
STEP 9:
Make wiring connections per the Electrical Connections
section on the next two pages.
1
(2) Installation
Support Cables
Luminaire Mount
Screws
Wiring Knockout
Conduit Knockouts
Locations
(4) Luminaire Mount Screws
Mounting Box
3
2
(2) Keyhole
Knockouts
(4) 1/2" threaded holes
(4) Mounting Holes
(4) Mounting
Holes
Conduit
Knockout
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed
including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant l’installation.
2. When handling, hold luminaire on sides to prevent damage to the top screen or LED’s.
3. This luminaire must be installed in accordance with the NEC or your local electrical
code. If you are not familiar with these codes and requirements, consult a qualied
electrician.
Ce produit doit être installé conformément à NEC ou votre code électrique local.
Si vous n’êtes pas familier avec ces codes et ces exigences, veuillez contacter un
électricien qualié.
SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE

Summary

Important Safeguards

Safety Instructions Overview

Follow all basic safety precautions when using electrical equipment, including disconnection before installation.

Handling and Code Compliance

Handle luminaire carefully to prevent damage and install according to NEC or local electrical codes.

Installation Steps

Wall Mounting - Box Preparation

Prepare mounting box, check knockouts, select hardware, use 3/16" mounting holes.

Wall Mounting - Box Placement

Position mounting box over junction box or conduit, note inspection knockout.

Wall Mounting - Surface Wiring

Utilize 1/2" threaded holes for surface wiring as needed.

Wall Mounting - Sealing

Apply silicone bead on gasket for uneven surfaces to ensure weather seal.

Wall Mounting - Conduit

Use luminaire knockouts for mounting over surface-mounted conduit.

Wall Mounting - Securing Box

Ensure mounting box is level and secure it to the wall surface.

Wall Mounting - Support Cables

Hook installation support cables onto the top screws of the mounting box.

Wall Mounting - Wiring Preparation

Prepare to make wiring connections as per the Electrical Connections section.

Installation Completion

Unhook support cables, slide luminaire onto mounting box screws, and tighten.

Electrical Connections

Terminal Block Connections

Connect fixture leads (black, white, green) to corresponding supply wiring terminals.

Wiring Diagram

Visual guide showing supply wiring to luminaire connections for Line, Neutral, and Ground.

Cree Edge Series Specifications

General

Warranty	10 years
IP Rating	IP66
Housing Material	Die-cast aluminum
Lens Material	Polycarbonate
CRI	80
Input Voltage	120-277V
Operating Temperature	-40°C to 50°C
Lifetime	100, 000 hours
Dimmable	0-10V dimming