Cres Cor H137 Series - User Manual

Insulated
Hot Cabinets
FL-2355-BC
Rev. 5 (8/22) Page 1 of 8
Call Toll-free: 877-CRES COR (273-7267) • Fax: 800-822-0393 • www.crescor.com
OPERATING and MAINTENANCE INSTRUCTIONS
Model: H137 series Humidity Holding Hot Cabinets
BUC-EE’S PROGRAMMING REVISION J-08
5925 Heisley Road • Mentor, OH 44060-1833
ELECTRICAL SPECIFICATIONS:
Model No. Volts Watts Amps Hertz Phase NEMA
H137WSUA5DMFBC
H137WSUA12DMFBC
120 2000 16.7 60 1 5-20P
H137WSUA12DMF208BC
208 2000 9.6 60 1 6-15P
HOW TO INSTALL UNIT:
1. Place cabinet on level oor, in a well ventilated area.
2. Unpack and install inner pan slides parts.
3. Plug cord end into proper wall outlet.
Air is VERY HOT when door is opened.
1. Push the switch on; the light will come on.
NOTE: The letters “LOTPR” (Low Temperature)
will show on the control panel until it
reaches 80°F (26°C).
2. Push and hold knob for 5 seconds, then turn to
show 220°F. Push the knob to set the temperature.
Run the unit for one (1) hour.
3. Push the switch o the unit o and let cool.
4. Wipe the inside clean with detergent and hot water.
FIRST TIME OPERATION:
NOTE: A new cabinet needs to “burn o”
manufacturing oils and excess adhesive
before its rst use. Do NOT load food into
cabinet until this has been done!
HOW TO CHANGE FROM °C TO °F (if needed)
1. Push the switch on; the light will come on.
2. Push and hold the “SET” button and the button in
the lower left hand corner together for 5 seconds.
You are now entered into the menu.
3. Scroll over the”Unit” and change it to “C” , then
scroll to the “END”.

Summary

OPERATING and MAINTENANCE INSTRUCTIONS

ELECTRICAL SPECIFICATIONS

Lists electrical data like volts, watts, amps, phase, and NEMA for various models.

HOW TO INSTALL UNIT

Step-by-step guide for cabinet placement, part installation, and power connection.

HOW TO CHANGE FROM °C TO °F

Instructions for switching temperature display between Celsius and Fahrenheit.

SAFETY WARNING

Critical safety advice regarding hot air release from the cabinet.

FIRST TIME OPERATION

Initial use procedures, including burn-off cycle and temperature setting.

OPERATING PROCEDURES

HOW TO HOLD

Instructions for dry holding food without humidity, including temperature settings.

HOW TO HOLD WITH HUMIDITY

Guide for holding food with humidity, detailing water pan filling and humidity settings.

DIGITAL CONTROL NOTES

Explanations of control panel displays for actual temperature and humidity readings.

UNIT OPERATION AND CLEANING

AUTOMATIC WATER FILL

Steps for connecting and using the automatic water fill feature.

UNIT SHUTDOWN PROCEDURE

Steps to properly shut down the unit after use.

UNIT CLEANING GUIDE

Detailed instructions for cleaning the cabinet interior and exterior, including stain removal.

MAINTENANCE AND TROUBLESHOOTING

DOOR LATCH ADJUSTMENT

Procedures for adjusting the door latch for vertical and horizontal alignment.

DAILY MAINTENANCE

Routine daily tasks including draining the water pan and cleaning the interior.

WEEKLY MAINTENANCE

Weekly checks for hinges and latch adjustments.

MONTHLY MAINTENANCE

Monthly checks for cooling fan operation.

TROUBLESHOOTING INITIAL CHECKS

Basic checks to perform if the unit is not working correctly.

TROUBLE-SHOOTING CHART

FAILURE AND POSSIBLE CAUSES

A chart correlating common failures with their potential causes.

CONTROLLER ERROR CODES

Explanation of error codes displayed on the controller, like 'err 00' and 'err 01'.

REPLACEMENT PARTS

REPLACEMENT PARTS LIST

Lists part numbers for various components for 120V and 208V models.

WIRING DIAGRAM

ELECTRICAL SCHEMATIC

Visual representation of the unit's electrical connections and components.

MAINTENANCE SCHEDULE

MAINTENANCE FOR CO151 MODELS

Daily, weekly, and monthly tasks for CO151XWUA5DXMBC and CO151FWUA12DXBC models.

MAINTENANCE FOR H137 MODELS

Daily, weekly, and monthly tasks for H137WSUA5DMFBC, H137WSUA12D*BC, H137PWSUA12D*BC.

Cres Cor H137 Series Specifications

General

Brand	Cres Cor
Model	H137 Series
Category	Humidifier
Language	English