CruzPro FU60 User Manual

Introduction
The FU60 digital fuel gauge provides a highly accurate
display of fuel remaining, trip fuel, total fuel used, fuel
consumption rate and "Time-To-Go" at current rate.
Fuel can be displayed with a resolution of 0.1 liters or
gallons or as a percentage (0 to 100%). The FU60
"learns" your tank and fuel sender characteristics and is
accurate with any tank shape. It is compatible with all
popular resistive fuel senders, both American and
European. Low and High Fuel alarms can be set and the
built-in 85 dB alarm will sound and the display will flash.
Five levels of backlighting can be selected and all setup,
calibration constants, alarm values, etc. are saved in a
nonvolatile memory. The FU60 outputs NMEA 0183
serial data or this terminal may be programmed to
activate an external alarm
or fuel transfer pump if using
a day tank. The FU60 contains a full data editor that can
be used to enter or edit the fuel data & sender resistance
values.
Page 3
CruzPro
FU60
Page 18
Other CruzPro Products
l Depthsounders & Speed/Temperature/Logs
l PC Based Fishfinders and Active Depth Transducers
l DC Volts/Amps/Amp-Hour Monitor
l AC Volts/Amps/Freq/kW Monitor
l LPG/Petrol Gas Detectors/Alarms
l Bilge Water Alarms & Smart Bilge Pump Controllers
l Windlass Controller/Chain Counter
l Digital Fuel Gauge & Fuel Consumption Calculator
l Digital Gauge for Three Tanks /w Separate Alarms
l Four Step Smart Alternator Regulators
l Marine Security System
l RPM/Engine Hours/Elapsed Time Gauges
l Digital Oil Pressure Gauge/Alarm
l Digital Water Temperature Gauge/Alarm
l One and Three Bank Digital Volts and Amps Gauges
l Digital Clock/Watch/Race Timers/Alarms
l 8 and 16 Amp Light Dimmers / Motor Speed Controller
l Solar Panel Charge Controllers 6/8/9 & 20 Amps
l 4 & 8 Channel NMEA Combiners/RS-232 Convertors
l Engine/Exhaust Temp. Monitor & Digital Pyrometer
l Remote Digital NMEA 0183 Data Repeaters
Intelligent Digital Fuel Gauge/w
Alarms & Consumption Calculator
key again results in the next set of data being displayed.
To leave the data editor, use the  key to scroll to the
word "dONE" and press the  key to exit.
Selecting USA or European Default Sender
In order for the gauge to be usable before calibration, a
default set of tank calibration and sender data is factory
pre- programmed into the FU60 fuel gauge.
The factory default setup for the FU60 is for a 100.0
gallon or liter tank with a 10-180 ohm American type
sender. To switch between 10-180 ohm USA and
240-33 ohm European type sender, press and hold the
t key for five seconds when power is applied (until you
see the "USA" or "EU" letters). Use the t and s keys
to switch between USA and EU and press the : key to
save your entry.

CruzPro FU60 Specifications

General

Brand	CruzPro
Model	FU60
Category	Measuring Instruments
Language	English

Summary

Introduction

Specifications

Installation

Mounting and Wiring

Details the process of mounting the instrument and connecting wires.

Operation

Backlight Intensity

Adjusts the screen brightness level for nighttime viewing.

Setting Low/High Fuel Alarms

Configures audible and visual alarms for low and high fuel levels.

Enabling/Disabling Alarms

Controls the arming or disarming of the fuel alarms for temporary silencing.

Checking Fuel Remaining

Displays current fuel level in liters, gallons, or percentage.

Checking Total Fuel Used or Trip Fuel Used

Shows total fuel consumed since last refill and trip fuel used.

Checking/Resetting Fuel Consumption Rate

Displays and resets the fuel consumption rate per hour.

Checking "Time-To-Go" at Current Consumption Rate

Calculates estimated time remaining based on current fuel consumption.

Setup and Calibration

Fuel/Sender Data Editor Operation

Manually enter or edit fuel level vs sender resistance data for calibration.

Selecting USA or European Default Sender

Switches between American (10-180 ohm) and European (240-33 ohm) sender types.

VERY IMPORTANT Notes