Cub Cadet BV428

IMPORTANT: READ OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES BEFORE OPERATING THE UNIT.
Removing Unit From Carton
Assemble The Unit
Starting The Unit
Insert upper blower tube
into blower outlet and turn
clockwise until it locks into
place.
Place the lower blower tube
onto upper blower tube and
turn clockwise until it locks
into place.
Assemble The Unit
Place unit on a level surface.
Fill fuel tank.
Press primer bulb 10 times,
or until fuel is visible
Move choke lever to
Position 1.
DO NOT squeeze throttle
control.
Pull rope 5 times. Move choke lever to
Position 2 .
Pull rope 3-5 times to start
engine. Squeeze throttle
control and allow unit to
warm up for 30 - 60
seconds.
Continue to squeeze
throttle. Move choke lever
to Position 3.
Continue to squeeze
throttle. Warm unit for an
additional 60 seconds to
complete warm-up. Unit
may be used during this
time.
11 2
Remove all contents from
the carton.
5
6
7
19 10
3
Place the unit on a level
surface, remove the oil plug
from the crankcase, and pour
the entire bottle of oil into the
fill hole.
Crouch in starting position.
8
4
Starting The Unit
11
12
13
14
10 X
5 X
3-5 X
Starter Rope
Blower Outlet
Throttle Control
On/ Off Switch
Upper Blower Tube
Lower Blower Tube
DIDN’T START?
Repeat these instructions.
IF engine fails to start after 2 attempts,
move choke lever to position 3 and pull
the starter rope until engine starts
IF unit still fails to start, refer to operator’s
manual for additional starting and
troubleshooting information
Primer
Bulb
Primer Bulb
Oil Plug
No Tools Required
for Blower Assembly*
*For vacuum assembly, refer to
the Assembly section of the
operator’s manual.
BV428
4-Cycle Suitcase Blower/Vacuum
Operator’s Manual
769-08089 P00 03/12
NEED HELP? Call 1-877-282-8684 in U.S. or 1–800–668–1238 in Canada
ENGLISH — PAGE 1
FRANÇAIS — PAGE 7
ESPAÑOL — PAGE 13

Cub Cadet BV428 Specifications

General

Brand	Cub Cadet
Model	BV428
Category	Blower
Language	English

Summary

Fast Guide to Operation

Removing Unit From Carton

Steps to unpack and prepare the unit from its shipping container.

Assembling the Unit

Instructions for connecting blower tubes and adding oil to the engine.

Starting the Unit

Guide to starting the engine using primer, choke, and starter rope.

Rules for Safe Operation

General Safety Instructions

Essential safety rules for operating the unit, including personal protection.

Fuel and Oil Handling Safety

Precautions for handling gasoline, oil, and warnings about fuel types.

Operational Safety Warnings

Critical warnings regarding thrown objects, hot surfaces, and bystander safety.

Symbols and Controls Guidance

Explanation of safety symbols, controls, and operating procedures.

Know Your Unit

Unit Components and Applications

Identifies unit parts and lists common applications.

Assembly Instructions

Blower Assembly

Step-by-step guide to assembling the blower tubes.

Vacuum Assembly

Instructions for attaching vacuum tubes and bag.

Oil and Fuel Information

Recommended Oil and Fuel

Details on correct oil type, fuel type, and fuel blends.

Fueling Procedures

Safe practices for filling the fuel tank with gasoline.

Starting and Stopping Instructions

Manual Starting Procedure

Step-by-step guide for starting the engine using the pull cord.

Starting with Optional Accessories

Instructions for starting using electric starter or power bit accessory.

Stopping the Unit

Safe procedures for shutting down the engine.

Operating the Unit

Safe Operation and Positioning

Proper handling, body position, and general operating tips.

Using as a Blower

Techniques for effective blowing operations.

Using as a Vacuum

Instructions for vacuuming debris and emptying the bag.

Maintenance Schedule

Checking the Oil Level

Procedure for checking the engine oil level before operation.

Changing the Oil

Steps for draining and refilling the engine oil.

Air Filter Maintenance

Instructions for cleaning or replacing the air filter.

Rocker Arm Clearance Adjustment

Procedure for checking and adjusting valve clearance.

Cleaning and Storage

Cleaning the Unit

Guidelines for cleaning the exterior of the unit.

Storage Procedures

Instructions for storing the unit, including long-term storage.

Troubleshooting

Engine Will Not Start, Idle or Accelerate

Solutions for common engine starting and running issues.

Engine Lacks Power or Stalls

Troubleshooting steps for loss of power or engine stalling.

Specifications

Technical Specifications

Details on engine type, displacement, RPM, and capacities.

Optional Accessory

Electric Starter and Power Start Bit

Information on optional starting accessories and where to get them.

Manufacturers Limited Warranty

Warranty Service and Claims

How to obtain warranty service and required proof of purchase.

Warranty Exclusions

List of items and conditions not covered by the limited warranty.

Legal Rights and Limitations

Explanation of legal rights and limitations related to the warranty.