Need help?Do you have a question about the CUSTOM CARE US Series and is the answer not in the manual?
General| Brand | CUSTOM CARE |
|---|---|
| Model | US Series |
| Category | Water Filtration Systems |
| Language | English |
Details the factory preset backwash frequency and duration for the UF Series Filter.
Standard unit settings for flush frequency, backwash, and rinse durations.
Inlet/outlet handles point in flow direction, water passes through control valve.
Handles point to center, system isolated, untreated water supplied.
Inlet to valve, outlet to bypass, allows testing without disruption.
Inlet to bypass, outlet away from valve, shuts off water to building.
Warnings regarding plumbing, lubricants, sealants, and tank placement.
Lists essential site requirements like water pressure, temperature, and electrical.
Details the standard installation configuration for the UF filter system.
Explains the optional AutoFlush kit for automatic bottom drain flushing.
Describes clean water regeneration for high fouling potential, using surge tanks.
Details clean water regeneration combined with AutoFlush for high fouling potential.
Instructions for installing the bypass valve, inlet/outlet plumbing, and grounding.
How to install a ground clamp or jumper wiring for electrical grounding.
Guidelines for connecting the drain line, including flow control fitting and anti-siphon trap.
How to connect a ball valve to the bottom tank drain connection for periodic blowdown.
Steps to reverse wire orientation for AutoFlush configuration.
Instructions for connecting the NHWB to the control board for different configurations.
Steps to set the current time of day, including hour, minutes, and day.
Steps to program regeneration settings, alarms, and display options.
How to set the alarm buzzer ON/OFF and its start/end times.
How to turn the display backlight ON or OFF.
Outlines the regeneration sequence for a standard installation.
Steps for filling the system with water, checking for leaks, and performing initial flush.
Describes the five possible displays and how to scroll between them.
How to use and exit Vacation Mode to shut down the system during periods of non-use.
Explains regeneration process, manual initiation, and steps.
Steps to diagnose battery depletion and how to replace the control valve battery.
Information on alarms and how to interpret and report error messages.
Troubleshooting for blank or incorrect time displays on the PC board.
Causes and solutions for display not showing flow or incorrect regeneration times.
Troubleshooting for automatic regeneration not occurring as expected.
Troubleshooting when regeneration works manually but not automatically.
Causes and corrections for hard water, excessive regenerant use, or residual regenerant.
Troubleshooting for excess water in the regenerant tank and metering issues.
Causes and corrections for failure to draw regenerant or water running to drain.
Error codes and troubleshooting for motor movement sensing issues.
Error codes and troubleshooting for motor stalling during cycle position changes.
Error codes for motor running too long or timing out.
Error codes for motor issues related to finding the proper park position.
Troubleshooting for specific error codes related to motor state, cycle steps, leaks, and memory.
Lists part numbers and quantities for the front cover and drive assembly components.
Lists part numbers and quantities for the piston assembly components.
Lists part numbers for bypass valve, handles, and UF replacement tank.
Lists part numbers for injector assemblies and water meter components.
Lists part numbers for the 3/4" drain line assembly components.
Lists parts for various PVC and brass sweat fitting assemblies.
Lists parts for plastic male NPT and 1-1/4" plastic male fittings.
Lists parts for brass Shark Bite and John Guest elbow fittings.
Lists parts for 1-1/4" & 1-1/2" PVC solvent and other related fittings.
Details operating parameters like filtration level, flow rates, and pressure.
Details application parameters like pre-filtration, chlorine, iron, and pH levels.
Programming settings for the Standard installation configuration.
Programming settings for the Standard with AutoFlush configuration.
Programming settings for the Clean Water Regeneration configuration.
Programming settings for Clean Water Regeneration with AutoFlush.
Warranty coverage for controller, valve assembly, and UF membrane tank.
List of conditions and damages excluded from the warranty coverage.
Overview of system operation, display options, and troubleshooting common errors.
Quick steps for manual regeneration and bypass valve operation.
Instructions for resetting the time of day after a power outage.
Guide for adjusting time, days between regeneration, and alarm settings.
To Next Page