CYCLEBOARD | ROVER
QUICK START GUIDE
FOLDING / UNFOLDING HANDLE
SETUP
Please go to cycleboard.com and download the complete owner’s manual.
PLEASE READ THE OWNERS MANUAL AND ALL SAFETY AND WARNING LABELS THOROUGHLY BEFORE ATTEMPTING TO OPERATE THE CYCLEBOARD.
The CycleBoard comes with the handle folded down in the shipping box.
Pick up the CycleBoard by
the handle to lift out of box
Loosen clamp lever by rotating
it forward. Then press the
release tab downward to raise
handle to upright position.
After handle locks in place,
tighten the clamp lever on the
left side by rotating it clockwise
until it is “very” tight
TO UNFOLD:
TO FOLD:
Reverse the steps above:
1. Loosen the clamp lever by rotating it forward.
2. Press the release tab downward.
3. Lower the handle until it locks in the down position
4. Once the handle locks in the down position, tighten the clamp lever by rotating it backwards
PACKAGE CONTENTS:
CycleBoard Electric Vehicle
2 Front Wheels
2 Front Wheel Bolts
Battery Charger
3 Allen wrenches
Quick Start Guide
4 finger nuts (for hinging deck)
ALWAYS WEAR A HELMET AND APPROPRIATE SAFETY GEAR
FIG. 1 - HAND BRAKE LEVER FIG. 2 - THROTTLE FIG. 3 - SPRINGS
INSTRUCTIONS:
Your CycleBoard has been pre-assembled and only requires a few steps to prepare it to ride:
LCD Display Functions:
1. Long press the center button (power) to turn on/off Power to the display.
2. Short press the top button to increase the speed mode from 1-5.
3. Short press the bottom button to decrease the speed mode from 1-5.
4. After the display is powered on, short press the center button to toggle through the options for odometer, trip, error code and time.
5. After the display is powered on, long press the top button to turn the tail-light on/off..
Note: If the release tab is difficult to press, gently shift the handle forwards and backwards while pressing the release tab.
Note: The “Clamp Lever” is SPRING LOADED to allow the user to position the lever to their desired location. To rotate the clamp lever forward or backward
WITHOUT tightening or loosening it. Pull the clamp lever to the left away from the base of the handle to engage the spring and disengage the teeth
1 2 3
1. After opening the box, inspect the contents for any damage that may have occurred during shipping. If anything has been damaged,
contact us for replacement or repair.
2. The Hand brake lever and throttle (Fig 1 and Fig 2) are adjusted downward for shipping. Adjust the throttle and hand brake lever to your
desired location, then tighten the screws using the included Allen wrenches.
3. Fully charge your battery before riding for the first time. The light on your charger will change from red to green when the battery is fully
charged.
4. Check the hand brake on the left handlebar to ensure it is functioning properly.
5. The self centering springs in the front of the CycleBoard may initially make squeaking and clicking sounds when steering but will stop
after a short break in period. Shown in Fig 3.
RELEASE TAB
TIGHTEN
LOOSEN
CLAMP LEVER
Page 21
PRE-RIDE CHECKLIST
BRAKE
Check the brakes for proper function. When you squeeze the
lever, the brake should provide positive braking action.
FRAME
Check for cracks or broken connections. Although cracked or
broken frames are rare, it is possible for an aggressive rider to
run into a curb or wall and wreck, bend or break a frame. Get into
the habit of inspecting your CycleBoard on a regular basis.
WHEELS AND TIRES
Periodically inspect the tires for excess wear.
ŅĹüĜųĵƋĜų埱ųå
ŞųŅŞåųĬƼĜĹüĬ±ƋåÚ
. Always check to ensure wheel bolts are tight.
Note: Front tires with uneven wear can cause dangerous
conditions like speed wobble and should be replaced with new
tires.
STEERING
ALWAYS ensure the 4 underside bolts in the
front steering mechanism are tight before
riding. Add Loctite if they become loose.
HARDWARE
Check all parts such as nuts, bolts, cables, fasteners, etc. to
ensure they are secure and assembled correctly before riding. If
the CycleBoard is damaged or not functioning properly, do not
ride.
LAWS AND REGULATIONS
Always check and obey any local laws or regulations.
INSURANCE
Do not assume that your existing insurance policies necessarily
provide coverage for use of this product. Check with your
insurance company for information regarding insurance.
USAGE
Make sure you are physically and mentally ready and capable to
ride your CycleBoard. This is a motorized three-wheeled product
and riders must familiarize themselves with the characteristics
BEFORE RIDING, ALWAYS MAKE SURE TO THOROUGHLY CHECK YOUR CYCLEBOARD AND ENSURE IT IS SAFE TO OPERATE.
Note: Always wait 10 minutes after charging your battery before riding.
Note: Always wait 15 minutes after riding before re-charging your
battery.
Note: Always unplug your battery charger after the battery has finished charging.
Note: Charge your battery at least once per month if not in use for best battery care.
To Next Page
Need help?
General
