Cygnett ExoDrive - User Manual

EXODRIVE WIRELESS
VENT
USER MANUAL
Caution
1.
2. Do not expose to extreme weather conditions.
3. Do not place close to a magnetic strip or strip card
as it could cause magnetic failure.
4. Please keep charger a safe distance of at least 80cm
from any implantable medical devices to avoid medical
device interference.
5. This is not a toy and should be kept away from children.
6. In the case of the device overheating, please
disconnect immediately.
approved by the party responsible for compliance could
void the user’s authority to operate the equipment. Cygnett
takes no responsibility for damages caused by incorrect use
of its products. Made in China.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by
try to connect the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician
for help.
This device complies with part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Cygnett and the Cygnett logo are trademarks of Cygnett
Pty Ltd. Other brands and product names are trademarks or
registered trademarks of their respective holders.
Cygnett Pty Ltd,
858 Lorimer St, Port Melbourne,
Victoria 3207 Australia
Cygnett UK Limited,
London, WC2H 9JQ
Cygnett USA Inc,
3838 W Carson St,
Ste 220, Torrance, CA 90503
Cygnett EU,
2718RD Zoetermeer, The Netherlands
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
“FCC RF Radiation Exposure Statement Caution: To maintain
compliance with the FCC’s RF exposure guidelines, place the
product at least 20cm from nearby persons.”

Summary

General Safety Cautions

Product Handling and Environment

Do not disassemble, expose to extreme conditions, or place near magnetic strips. Keep away from children.

Medical Device Interference

Keep charger at least 80cm from implantable medical devices to prevent interference.

Overheating and Modifications

Disconnect if device overheats. Modifications not approved may void authority to operate.

FCC Compliance and Interference

Regulatory Compliance Notice

Equipment complies with FCC Part 15 limits for Class B digital devices to prevent harmful interference.

Interference Mitigation

User encouraged to correct interference by reorienting antenna, increasing separation, or changing circuit.

Installation Instructions

Vent Mounting

Attach product to vent by pushing spring-loaded clip, hooking onto vent blades, and releasing clip to grip.

Adjusting Viewing Angle

Loosen tightening ring on ball joint to adjust angle, then tighten ring to secure position.

Connecting Power Source

Connect Micro-USB to USB-A cable to charger input, plug USB-A into 12V car adapter, and into vehicle socket.

Wireless Charging Operation

Place device on charging output, secure with retractable arms. Press quick release button to remove device.

Product Specifications

Technical Details

Details include Name, Item Number, Input/Output specs, Frequency Bands, Max Output Power, and FCC ID.

Troubleshooting Charging Issues

Use supplied adapter, ensure QC 3.0/12V output. Align device centrally and remove thick/metallic cases.

Cygnett ExoDrive Specifications

General

Brand	Cygnett
Model	ExoDrive
Category	Cell Phone Accessories
Language	English