D-Link DSL-2790U Quick Installation Guide

ENGLISH
DSL-2790U
If any of the above items are missing, please contact your reseller/retailer.
Wireless N300 ADSL2+ Modem Router (DSL-2790U)
Power Adapter
Ethernet Cable
xDSL Microlter/Splitter & Cable
Quick Install Guide
1
Power LED A solid green light indicates a proper connection to the power supply.
2
LAN (1~4) LEDs
A solid green light indicates a connection to a device. The light will
blink during data transmission.
3
Wi-Fi LED
A solid green light indicates that the Wi-Fi is ready. The light will blink
during data transmission.
4
WPS LED The light will blink during the WPS process.
5
USB LED A solid green light indicates a connection to a USB device.
6
ADSL LED
A solid green light indicates a proper connection to the ADSL enabled
telephone line.
7
Internet LED
A solid green light indicates a proper connection to your broadband
service. The light will blink during data transmission.
8
xDSL Port
Connect to an ADSL enabled telephone line and the supplied
microlter/splitter.
9
LAN (1~4) Ports
Connect Ethernet devices such as computers, switches, and game
consoles.
10
USB Port Connect USB devices such as printers, storage or 4G/LTE adapters.
11
Wi-Fi Button Press to enable/disable Wi-Fi network
12
WPS Button Press to enable WPS
13
Power Button Press to turn on or o the device.
14
Power Port Connect the supplied power adapter.
15
Reset Button
Press to reset the device to factory default settings, located on the
under side of the device near the serial number sticker.
10
11
12
13
14
1
Connect your existing Phone cable from the telephone outlet to the LINE
port on the Microlter and your telephone handset into the PHONE port.
2
Connect the Phone cable from the DSL port on the Microlter to the DSL
port of the modem router.
3
Connect the Ethernet cable from the LAN port of the modem router to the
Ethernet port on your computer.
4
Plug the power adapter into your modem router and connect to an available
power outlet.
5
6
After the modem router has powered up, verify that the Power and ADSL
LEDs are both lit.
Continue with the Conguration section on the other side of this document.
Microlter
Telephone Outlet
Package Contents
QUICK INSTALLATION GUIDE
Hardware Overview Minimum Requirements Connect your Modem Router
• Internet Provider Account Details - If you are using an Australian or New
Zealand ADSL connection, you will need your user name and password. If you do
not have this information, contact your Internet provider.
Do not proceed until you have this information.
Before you Start
Internet Requirements:
• An activated ADSL telephone line and account with an Internet provider
or
• An active NBN/UFB connection and account with an Internet provider
Web-based Conguration Requirements:
Device with the following:
• An installed Ethernet adapter or wireless adapter
Supported Browsers:
• Internet Explorer 7 or higher
• Safari 4 or higher
• Chrome
• Firefox
mydlink™ Requirements (optional):
• iPhone/iPad/iPod Touch (iOS 3.0 or higher)
• Android device (1.6 or higher)
• Web Browser Requirements:
• Internet Explorer 7 or higher
• Safari 5 or higher
• Chrome
• Firefox
If you experience issues conguring this Modem Router, try performing a hard reset
by using an unfolded paperclip to press and hold the reset button for 10 seconds
while the Modem Router is powered on.
Wireless N300
ADSL Modem Router
1 3 5 7 9
2
4
6 8
Power Adapter
DSL-2790U
Computer
LINE
PHONE
Phone Cable
DSL-2790U
Microlter
Ethernet Cable
DSL-2790U
Computer
15

D-Link DSL-2790U Specifications

Ports & interfaces

RJ-11 ADSL port	1
RJ-45 Ethernet ports	4 x 10/100BASE-TX
USB port	1 x USB 2.0

Power

Input voltage	100~240 V (±20%)
Input frequency	50~60 Hz
Output voltage	DC 12 V
Output current	1 A

Operating Environment

Operating temperature	0 to 40 °C (32 to 104 °F)
Non-operating temperature	-20 to 65 °C (-4 to 149 °F)
Operating humidity	0% - 90% non-condensing
Non-operating humidity	5% - 95% non-condensing

Weight and Dimensions

Dimensions	68 x 42 x 51 mm (2.68 x 1.65 x 2 inches)
Weight	113.4 grams (4 ounces)