Daewoo DIM-70 - User Manual

Questions and Answers

S
Sherry HuntAug 16, 2025
Why my Daewoo DIM-70 Ice Maker doesn’t operate?
- L
  Linda MaldonadoAug 16, 2025
  Your Daewoo Ice Maker might not be operating due to several reasons: it may be unplugged (plug it in), the fuse may be blown (replace the fuse; if it happens again, call for service), the power switch may be off (turn it on), the voltage of the power supply may be low (add a manostat), the ice cube full sensor might be damaged (replace it), or the ice storage bin may be full (remove some ice and ensure the ice-full sensor is free of ice).
B
Brian BarnesAug 22, 2025
What to do if my Daewoo DIM-70 Ice Maker makes ice, but the bin doesn't fill up?
- M
  michelle25Aug 22, 2025
  If your Daewoo Ice Maker makes ice, but the bin doesn't fill, consider these potential causes: the condenser may be dirty (clean the condenser), the bin drain may be partially restricted (clean out the drain and check the installation), the airflow to the ice maker may be obstructed (check the installation), the hot gas valve performance may be poor (replace the hot gas valve), the sprinkler may be partially clogged (clean the sprinkler), the spraying of the small nozzle may be blocked by the ice slideway (adjust the location of the ice slideway), the water quality may be too poor (install a filter apparatus in front of the water inlet valve), or the ambient and water temperatures may be high (check the installation).
M
Michael MacdonaldAug 25, 2025
Why is my Daewoo Ice Maker leaking water?
- P
  perezhannahAug 26, 2025
  Water may be leaking from your Daewoo Ice Maker for several reasons: a few water drops may fall when you open the door (this is normal condensation), the water supply connection may be leaking (tighten the fitting), the nut of the water drain hole may be leaking (tighten the nut), or the drainpipe connection may be leaking (tighten the fitting).
J
james43Aug 28, 2025
What to do if water doesn't feed in after starting my Daewoo DIM-70 Ice Maker?
- R
  Rachel JuarezAug 28, 2025
  If water isn't feeding into your Daewoo Ice Maker after it starts, check if the water supply tap is turned off (turn it on), the water supply pressure is too low (adjust the water supply pressure within the stated range), the water inlet valve is damaged (replace the water inlet valve), or the water supply pipe is not properly connected (reconnect the water supply pipe).
J
James WebsterAug 31, 2025
How to prevent scales occurring frequently inside my Daewoo DIM-70 Ice Maker?
- J
  Joshua HernandezAug 31, 2025
  Scales may occur frequently inside your Daewoo Ice Maker if the hardness of the water is too high (use a water-softening device installed in front of the water inlet valve), or the sprinkler is blocked (clean it), or the sprinkler pressure of spray isn't enough (check the water quality; the water line may be blocked).
T
Todd ReidSep 3, 2025
Why is harvesting ice difficult in my Daewoo DIM-70?
- J
  John JonesSep 3, 2025
  Harvesting ice might be difficult in your Daewoo Ice Maker if the water supply tap is turned off (turn on the water supply tap), or the ambient and water temperature are too low (adjust the temperature).
C
Craig BryantSep 6, 2025
Why is my Daewoo Ice Maker making noise during operation?
- A
  Alexander HopkinsSep 6, 2025
  Your Daewoo Ice Maker may be making noise during operation because the feet are not leveled and locked (level and lock the feet). Certain sounds are normal.
D
Dr. Taylor MontesSep 9, 2025
What to do if the body of my Daewoo DIM-70 is electrified?
- P
  Pamela SmithSep 9, 2025
  If the body of your Daewoo Ice Maker is electrified, it could be because the grounding line isn't in the socket (use a socket meeting the required electrical standard), or the lines are creepage (adjust, reconnect/replace lines).
W
Wesley DavisSep 10, 2025
Why does my Daewoo DIM-70 stop suddenly while making ice?
- A
  angela22Sep 12, 2025
  Your Daewoo Ice Maker might stop suddenly due to: the electricity being off (reconnect the power supply line), the room temperature being out of the stated range (cut off the electricity and let the ice maker stop working until the temperature returns within the stated range), the fuse being blown (replace the fuse), the voltage of the power supply being low (add a manostat), or the ventilation louvers being covered (remove the obstruction).
Z
zjamesSep 12, 2025
Why are the ice cubes from my Daewoo DIM-70 too big?
- M
  Mackenzie BellSep 12, 2025
  Ice cubes from your Daewoo Ice Maker might be too big if the ambient temperature and water temperature are too low (adjust the temperature).