Why Daewoo Water Dispenser cooling time longer than normal?
If the cooling time is longer than normal, the condenser surface might be covered in dust, so clean out the dust. There could be refrigerant leakage or loss, so add refrigerant or repair it. The compressor might also be failing, so fix or replace it.
Why Daewoo DWC-42R Water Dispenser has foul odor in air around dispenser?
The foul odor could be because the hot water tank is empty or not completely full. Press the hot dispenser button until water flows to remove air from the hot tank.
What to do if the Daewoo Water Dispenser machine working in condition but heating light off?
If the machine is working but the heating light is off, the PCB connection might be loose, so fix up the connection. The LED might be struck down, so replace it. The PCB could also be burnt out, so replace it.
What to do if Daewoo Water Dispenser hot and cold water mixed?
If hot and cold water are mixing, hot water steam might be flowing into the cooling tank; check and eliminate it. The thermostat could be invalid, so replace it. Also, the check valve might be failing, so replace it.
Why Daewoo Water Dispenser heating system goes on working?
If the heating system is continuously running, it is possible that the temperature controller is invalid and needs replacement.
Why is there no cold water from my Daewoo DWC-42R Water Dispenser (compressor cooling)?
If there's no cold water, the cold switch might be invalid, requiring fixing or replacement. The PTC could be mangled, so replace it. The Thermostat I might also be invalid, so adjust or replace it. Finally, the cooling system could be blocked, requiring repair by a maintenance center.
Why Daewoo DWC-42R Water Dispenser compressor starts frequent?
Frequent compressor starts can be due to evaporator frost, so seal the heat preservation foam. Alternatively, the PTC might be invalid, requiring replacement, or there could be a vacuumize shortage, requiring repair by an expert.
Why Daewoo DWC-42R Water Dispenser cooling system goes on working?
If the cooling system continuously runs, the environment temperature might be higher than normal; consider cooling or stopping the machine for a while. Refrigerant leakage could also be the cause, requiring repair by the manufacture center. Additionally, the thermostat might be malfunctioning, requiring adjustment or replacement.
What to do if my Daewoo DWC-42R water is not hot enough?
If the water isn't hot enough, it could be because you're using water too frequently in a short period. Wait for a moment and then use it again. Alternatively, there could be a connection terminal failure, requiring maintenance or replacement, or a Temperature control II failure, requiring replacement.
Why is there no hot or cold water from my Daewoo Water Dispenser?
If your Daewoo Water Dispenser isn't dispensing hot or cold water, it could be due to a couple of reasons. First, you might have used a lot of hot or cold water in a short period; if that's the case, just wait, and it should be available again. Second, check the power supply. Ensure the dispenser is plugged into a socket and that the heating or cooling switch is turned on.
Follow step-by-step instructions for operating the water dispenser, including bottle insertion and power activation.
Adhere to safety guidelines for placement, usage, and maintenance to prevent damage and ensure safe operation.
Follow precautions regarding power cord usage, grounding, and handling of electrical components to prevent hazards.
Guidelines on machine operation, including cooling switch delay, part replacement, and usage by persons with reduced capabilities.
Detailed instructions for cleaning the water dispenser, including initial flushing, disinfection, and surface washing.
Overview of the dispenser's technical data, including supply voltage, wattage, flow capacity, and dimensions.
Guidance on identifying and resolving common problems such as no hot/cold water or water leakage.
Follow step-by-step instructions for operating the water dispenser, including bottle insertion and power activation.
Adhere to safety guidelines for placement, usage, and maintenance to prevent damage and ensure safe operation.
Follow precautions regarding power cord usage, grounding, and handling of electrical components to prevent hazards.
Guidelines on machine operation, including cooling switch delay, part replacement, and usage by persons with reduced capabilities.
Detailed instructions for cleaning the water dispenser, including initial flushing, disinfection, and surface washing.
Overview of the dispenser's technical data, including supply voltage, wattage, flow capacity, and dimensions.
Guidance on identifying and resolving common problems such as no hot/cold water or water leakage.
General| Hot Water Temperature | 85-95°C |
|---|---|
| Cold Water Temperature | 5-10°C |
| Cooling Method | Compressor |
| Voltage | 220V |
| Material | Plastic and Stainless Steel |
To Next Page
