Daihen varstroj VARMIG 211 BD Supermig

To Next Page

N A V O D I L O Z A U P O R A B O

B E D I E N U N G S A N L E I T U N G

O P E R A T I N G I N S T R U C T I O N S

H A S Z N Á L A T I U T A S Í T Á S

U P U T S T V O Z A U P O R A B U

U P U T S T V O Z A U P O T R E B U

UPATSTVO ZA UPOTREBA

VARMIG 211 BD Supermig

VARMIG 251 BD Supermig

VARMIG 271 Supermig

VARMIG 331 Supermig

VARMIG 351 Supermig

DAIHEN VARSTROJ, varjenje

in rezanje ter robotizacija d.d

Industrijska ulica 4

SLO- 9220 Lendava

Tel:

fax:

E-mail:

url:

+ 386 (0)2 5788 820

+ 386 (0)2 5751 277

info@varstroj.si

http://www.varstroj.si

Prodaja:

Export:

Servis-tel:

Servis-fax:

+386 (0)2 5788 834, 835

+386 (0)2 5788 839, 840

+386 (0)2 5788 836, 879

+386 (0)2) 5751 646

SLIKA 1, BILD 1,

FIGURE 1, ÁBRA 1,

SLIKA 1, SLIKA 1

SLIKA 2, BILD 2,

FIGURE 2, ÁBRA 2,

SLIKA 2, SLIKA 2

SLIKA 3, BILD 3,

FIGURE 3, ÁBRA 3,

SLIKA 3, SLIKA 3

SLIKA 4, BILD 4,

FIGURE 4, ÁBRA 4,

SLIKA 4, SLIKA 4

SLO

SRB

BIH

MNE

MAK

Art.: 604947 v.2020.12

Need help?

Do you have a question about the Daihen varstroj VARMIG 211 BD Supermig and is the answer not in the manual?

Summary

1.0. SAFETY REGULATIONS

1.1. Installation of equipment

Regulations for the safe installation of the welding equipment.

2. DESCRIPTION OF THE MACHINE

Features

Key characteristics and capabilities of the welding machine.

Utilisation for intended purpose

Guidelines for the correct and intended use of the machine.

3. TECHNICAL DATA

8. CARE AND MAINTENANCE

9. AFTER-SALES SERVICES AND WARRANTY

UTILISATION FOR INTENDED PURPOSE ONLY

5. Varmig 211 BD, 251 BD, 271, 331, 351 Supermig functions description

5.1. Setting up the welding current

Adjusting the welding current using the 6-position switch.

5.2. Spot welding

Performing short welds using the spot welding function.

5.2 2 T (2-Stroke Welding Mode)

Operating the machine in 2-stroke welding mode.

5.3 4 T (4-Stroke Welding Mode)

Operating the machine in 4-stroke welding mode.

5.4 Spot welding with a semiautomatic - Switch

Performing spot welds using the semi-automatic feature.

5.5 Intermitted welding* with a semiautomatic - Switch

Performing welds with pauses using the semi-automatic mode.

5.6 Wire inching

Feeding the wire without welding.

5.7 Softstart

Understanding the automatic softstart feature.

5.8 Burnback

Understanding the automatic burnback function.

5.9 List of displayed errors

Interpreting error codes indicated by the LED diode.

6. PREPARING FOR WELDING

6.1. Mains connection

Connecting the welding machine to the power supply.

6.2 Mounting the wire spool

Installing the wire spool onto the holder.

6.3 Leading-through the wire

Threading the welding wire into the machine.

6.4 Gas cylinder

Setting up and connecting the gas cylinder.

7. MIG;MAG WELDING

7.1. Aluminium welding

Specific instructions for welding aluminum using MIG/MAG.

10. LIST OF SPARE PARTS

11. TROUBLESHOOTING

Machine Stopped Welding Suddenly

Diagnosing why the machine stops welding and the fan runs.

Machine Does Not Work After Power-On

Troubleshooting when the machine is on but inactive.

Intermittent or Bad Arc

Addressing issues causing a poor or unstable welding arc.

No Welding Current

Resolving the problem of no welding current with indicators on.

Machine Does Not Function When Torch Trigger Pressed

Fixing issues when the torch trigger fails to initiate machine function.

No Shielding Gas

Troubleshooting when only shielding gas is missing.

Poor Welding Properties

Identifying causes for generally poor welding results.

Irregular Wire Feed

Diagnosing inconsistent wire feeding during welding.

Insufficient Cooling Power

Addressing problems related to inadequate cooling of the machine.

Welding Parameters

Electric Connections

D.APPENDIX

D.1. Disposal of the device after its service life

Procedures for proper disposal of the appliance and its components.

D.2 RoHS compliance

Declaration of compliance with RoHS directive for supplied products.