Operation manual
7
EWAQ+EWYQ005~007ADVP
Packaged air-cooled water chillers and
packaged reversible air to water heat pumps
4PW71885-1 – 10.2011
Programming quiet mode
Programming quiet mode is carried out as follows.
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the quiet mode.
The selected mode is blinking.
You can leave programming by pressing the pr button.
3 Press the < button to confirm the selected mode.
The selected mode is blinking.
4 Use the pi and pj buttons to consult the programmed
actions.
This is called the readout mode. Empty program actions (e.g. 4
and 5) are not displayed.
You can return to step 2 by pressing the pr button.
5 Press the < button for 5 seconds to enter the programming
mode.
You can return to step 4 by pressing the pr button.
6 Use the < button to select the action number you would like to
program or to modify.
7 Use the pi and pj buttons to set the correct action time.
8 Use the ba button to select or deselect x as action.
9 Repeat steps 6 to 8 to program the other actions of the selected
mode.
When all actions have been programmed, make sure that the
display shows the highest action number you would like to save.
10 Press the < button for 5 seconds to store the programmed
actions.
If the < button is pressed when action number 3 is displayed,
actions 1, 2 and 3 are stored but 4 and 5 are deleted.
You automatically return to step 4. By pressing the pr button
several times, you return to previous steps in this procedure and
finally return to normal operation.
2.6.3. Consulting programmed actions
Consulting cooling or heating actions
Consulting cooling or heating is carried out as follows.
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the mode (current
mode or quiet mode) you want to consult.
The selected mode is blinking.
You can leave consultation by pressing the pr button.
To consult quiet mode, refer to " Consulting quiet mode actions"
on page 7.
3 Press the < button to confirm the selected mode.
The actual day is blinking.
4 Select the day you would like to consult by means of the pi
and pj buttons.
The selected day is blinking.
You can return to step 2 by pressing the pr button.
5 Press the < button to confirm the selected day.
The first programmed action of the selected day appears.
6 Use the pi and pj buttons to consult the other
programmed actions of that day.
This is called the readout mode. Empty program actions (e.g. 4
and 5) are not displayed.
You can return to step 4 by pressing the pr button.
Consulting quiet mode actions
Consulting quiet mode is carried out as follows.
1 Press the < button.
The actual mode is blinking.
2 Use the pi and pj buttons to select the quiet mode.
The selected mode is blinking.
You can leave programming by pressing the pr button.
3 Press the < button to confirm the selected mode.
The selected mode is blinking.
4 Use the pi and pj buttons to consult the programmed
actions of that day.
This is called the readout mode. Empty program actions (e.g. 4
and 5) are not displayed.
You can return to step 2 by pressing the pr button.
2.7. Tips and tricks
Programming the next day(s)
After confirming the programmed actions of a specific day (i.e. after
pressing the < button for 5 seconds), press the pr button once. You
can now select another day by using the pi and pj buttons
and restart consulting and programming.
Copying programmed actions to next day
In heating/cooling program it is possible to copy all programmed
actions of a specific day to the next day (e.g. copy all programmed
actions from "1" to "2").
NOTE
Returning to previous steps in the programming
procedure without saving modified settings is done by
pressing the pr button.
5 sec
5 sec
SAVE NO SAVE
NOTE
Consulting cooling or heating is done in the same way.
At the start of the consulting procedure, cooling or
heating operation is selected. After that, you have to
return to the start of the consulting procedure to
consult the other operation mode.
To Next Page
Loading...
