Why is my Daikin FTXS35CVMB(9)(8) Air Conditioner cooling/heating poorly?
Several factors might be causing a poor cooling or heating effect. Make sure that: * The air filters are clean. * Nothing is blocking the air inlet or outlet of the indoor and outdoor units. * The temperature setting is appropriate. * The windows and doors are closed. * The airflow rate and direction are set correctly. * The unit is not set to INTELLIGENT EYE mode.
Why does my Daikin FTXS35CVMB(9)(8) Air Conditioner indoor unit smell?
The indoor unit may emit an odor because smells from the room, furniture, or cigarettes are absorbed into the unit and discharged with the airflow. If this occurs, it's recommended to have the indoor unit cleaned by a technician. Consult the service shop where you purchased the air conditioner.
Why my Daikin FTXS35CVMB(9)(8) Air Conditioner operation does not start immediately?
If the ON/OFF button was pressed soon after the operation was stopped, or when the mode was reselected, you should wait for about 3 minutes.
Why does my Daikin FTXS35CVMB(9)(8) Air Conditioner heating stop suddenly with a flowing sound?
The system is likely removing frost from the outdoor unit. Please wait for approximately 4 to 12 minutes.
Why doesn't hot air flow out immediately from my Daikin FTXS35CVMB(9)(8) Air Conditioner after starting the heating operation?
The air conditioner is warming up. You should wait for 1 to 4 minutes.
Why is the cooling or heating effect poor in my Daikin FTXS35CVMB(9)(8)?
If your Daikin Air Conditioner isn't cooling or heating well, check these: * Ensure the air filters are clean. * Remove any obstructions blocking the air inlet or outlet of the indoor and outdoor units. * Verify the temperature setting is correct. * Make sure all windows and doors are closed. * Confirm the airflow rate and direction are appropriately set. * Check if the unit is set to INTELLIGENT EYE mode.
What to do if my Daikin FTXS35CVMB(9)(8)'s heating stops suddenly and I hear a flowing sound?
If the heating operation of your Daikin Air Conditioner stops suddenly and you hear a flowing sound, wait for about 3 to 8 minutes.
What to do if my Daikin Air Conditioner does not operate and the OPERATION lamp is off?
If your Daikin Air Conditioner isn't operating and the OPERATION lamp is off, consider these possible causes: * Check if a breaker has turned OFF or a fuse has blown. * Verify there isn't a power failure. * Ensure batteries are correctly set in the remote controller. * Confirm the timer setting is correct.
Why did my Daikin FTXS35CVMB(9)(8) stop suddenly with the OPERATION lamp on?
The air conditioner might stop operating due to a sudden large voltage fluctuation, as a system protection measure. It will automatically resume operation in about 3 minutes.
What to do if my Daikin FTXS35CVMB(9)(8) Air Conditioner stops suddenly and the OPERATION lamp flashes?
If your Daikin Air Conditioner stops suddenly and the OPERATION lamp flashes, clean the air filters or remove any obstacles. Turn the breaker OFF, then turn it back ON, and try operating the air conditioner with the remote control. If the lamp continues to flash, it is recommended to call the service shop where you bought the air conditioner.
General| Brand | Daikin |
|---|---|
| Model | FTXS35CVMB(9)(8) |
| Category | Air Conditioner |
| Language | English |
Essential safety warnings and precautions for operating and handling the unit.
Lists and compares the functions available in high-grade models.
Lists and compares the functions available in standard grade models.
Lists and compares the functions available in non-inverter models.
Provides detailed technical specifications for cooling-only models.
Provides detailed technical specifications for heat pump models.
Identifies connectors and components on the indoor unit PCB.
Details wiring and connectors for outdoor units (ARK(X)S-C series).
Explains key operational principles like frequency control and airflow.
Describes the role of thermistors in heat pump and cooling-only models.
Details mode hierarchy, frequency control, and various operational controls.
Discusses the importance of proper handover and user explanation.
Provides essential safety precautions and instructions for operation.
Highlights errors detected by operation lamp and signal transmission.
Lists common symptoms and their corresponding checks and measures.
Explains how to access and interpret error codes via the remote control.
Provides error codes, descriptions, and troubleshooting steps for various issues.
Details the removal steps for air filters, front grille, and other indoor unit parts.
Covers removal of panels, fan motors, and electrical boxes for outdoor units.
Guides on performing trial operations using the remote control.
Explains jumper settings for specific functions like auto-restart.
Illustrates refrigerant piping for indoor and outdoor units in cooling and heat pump modes.
Shows electrical connections for indoor and outdoor units.
To Next Page