EasyManua.ls Logo

Daken DK120 - User Manual

Default Icon
9 pages
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
1
Finishing Mower
DK120, DK150, DK180
Operators Manual & Parts List
Clark Equipment P/L
30 Salisbury Road Hornsby NSW 2077
Phone Toll Free 1800 636 451

Questions and Answers

  • T
    Tyler ClarkAug 15, 2025
    Why Daken DK120 Lawn Mower has vibration?
    • V
      Victor WebbAug 15, 2025
      If your Daken Lawn Mower exhibits vibration, the issue might stem from an imbalance. Inspect the blades for any bending, damage, or breakage. Depending on your findings, either repair the affected blades or replace them as needed.
  • D
    David CabreraAug 18, 2025
    What to do if Daken Lawn Mower clutch slips?
    • R
      reynoldsangelAug 18, 2025
      If the clutch on your Daken Lawn Mower is slipping, it could be due to several reasons. First, you might be overloading the mower, in which case, try slowing down. Second, the clutch might be loose; try tightening the springs on the clutch plates. Finally, the clutch components might be worn out, requiring replacement of the clutch components or the entire assembly.
  • S
    Sharon LeblancAug 21, 2025
    Why is my Daken DK120 leaving grass?
    • L
      Laura KaufmanAug 21, 2025
      If your Daken Lawn Mower is leaving grass behind, it could be due to traveling too fast. Try slowing down your pace. Alternatively, the top link might be too short. In this case, extend the top link.
  • V
    Vincent WilkinsonAug 25, 2025
    How to improve poor cutting job of Daken Lawn Mower?
    • R
      Robert DuranAug 25, 2025
      If your Daken Lawn Mower is not cutting properly, it could be because you are traveling too fast; try slowing down. Another possibility is that the blades are dull, in which case you should sharpen them.
  • C
    Christopher BurgessAug 28, 2025
    Why is Daken DK120 gearbox noisy?
    • J
      John WhiteAug 28, 2025
      A noisy gearbox in your Daken Lawn Mower may be caused by poor gear mesh. To resolve this, remove the input shaft and gear, replace any worn parts, and reassemble. Use shims to achieve a gear backlash of 0.006-0.018 inches, measured at 2 13/16” from the shaft centerline.
  • M
    Miss Jessica RodriguezAug 31, 2025
    What to do if Daken Lawn Mower is scalping?
    • T
      Teresa CarrAug 31, 2025
      If your Daken Lawn Mower is scalping the lawn, it is likely set too low. Try raising the mower to a higher setting.
  • H
    Hannah KingSep 3, 2025
    Why Daken Lawn Mower makes grooves in grass?
    • B
      Brandon BlakeSep 3, 2025
      If your Daken Lawn Mower is creating grooves in the grass, the blades may be bent. Straighten the blades or replace them.
  • K
    Katie HaneySep 6, 2025
    What to do if Daken Finishing Mower doesn’t turn?
    • J
      jamiepaceSep 6, 2025
      If the Finishing Mower of Daken doesn't turn, the tractor clutch might be slipping. Try tightening or replacing the slip clutch. Alternatively, the PTO shaft might be slipping; in this case, repair the tractor PTO clutch.
  • L
    Laurie CareySep 10, 2025
    Why Daken DK120 Lawn Mower has wheel failure?
    • H
      Heather LopezSep 12, 2025
      Wheel failure on your Daken Lawn Mower can occur if you are traveling too fast. Try slowing down.

Daken DK120 Specifications

General IconGeneral
BrandDaken
ModelDK120
CategoryLawn Mower
LanguageEnglish