Danmini YA-300-GSM User Manual

Security GSM Alarm System
YA-300-GSM
USER MANUAL
1 System Introduction
Wireless GSM intelligent anti-theft electronic alarm system is an innovative wireless mobile intelligent
warner integrating GSM digital signal processing techniques and imported STC microprocessor, and a variety
of technologies including digital voice announcer, English SMS, learning code, etc.
In addition, this alarm system is highly automatic, giving automatic voice or SMS alert in the event of
emergency without intensive manual settings required. Features of stability, reliability, safety, and humanizing
control enable it to be widely used for alert in shops, convenience stores, offices, villa as well as residential
communities.
2 Function Introduction
 4 wired and 6 wireless defence zones;
 Can preset and store 6 voice phones and 3 message phones;
 Remote two-way intercom，Built-in intercom speaker;
 Telephone (mobile phone) remote control programming;
 SMS remote control preset & arm/disarm the main panel;
 SMS alarm content can be changed;
 3 groups of timely arm and disarm;
 2 groups reply to timely control the home appliances open or close;
 Can connect wireless siren(Option)
 10-second automatic message recording;
 Built-in intelligent English message;
 Alarm locking memory and information clear for easy checking;
 One-key-control function: Out Arm, Home Arm, Remote Arm;
 Wireless intelligent learning encoding and comply additional accessories;
 Arm, disarm, monitor and intercom by remote calling the alarm unit;
 Real-time, delay, 24 hours, bypass defense zones programming function;

Danmini YA-300-GSM Specifications

General

Model	YA-300-GSM
Wireless Frequency	433MHz
Type	Security System
GSM Frequency	900/1800 MHz
Operating Temperature	-10°C to +50°C
Humidity	≤85% RH
Supported Sensors	Door, PIR, Smoke, Gas

Summary

System Introduction

Function Introduction

Technical Parameter

Factory Default

Installation

Main Unit Installation

Guidance on placing the main unit to avoid interference and ensure proper operation.

Main Unit Settings

Prompt Message

Details on beep prompts and defense zone indicator statuses for system feedback.

Remote Control Programming

Code Pairing by Remote Control

Procedure for pairing remote controls with the main alarm unit.

Delete Remote Control

Instructions for removing paired remote controls from the system.

Code Pairing of Defence Zone

Steps to pair wireless sensors with specific defence zones.

Delete Code Pairing

Procedure to remove defence zone sensor pairings.

SMS Instructions

Details on controlling the alarm system via SMS commands.

Change Password

Instructions for modifying operation and programming passwords for security.

Phone Setting

Configuration options for phone-based notifications and control.

Voice Call

Setting up voice alerts to specified phone numbers.

Phone Number Settings

Configuring phone numbers for voice alarm notification.

Message Receiving Phone Number

Configuring phone numbers for SMS alarm notifications.

Defence zone Programming

Detailed configuration of defence zones, types, and locations.

Defence zone at Home

Setting specific defence zones for 'arm at home' mode.

Operating Siren

Configuration for siren behavior during arm/disarm operations.

Custom the content of Zone Alarm Message

Customizing the text content of SMS alarm messages.

Clock Setting

Timing Setting

Timely Arm

Scheduling specific times for the alarm system to arm automatically.

Timely Disarm

Scheduling specific times for the alarm system to disarm automatically.

Timing Control

Enabling or disabling the timely arm/disarm function.

Timely Open Appliance

Scheduling times to automatically turn on connected home appliances.

Timely Close Appliance

Scheduling times to automatically turn off connected home appliances.

Operation Instruction

Arm while outside

Instructions for arming the system when no one is home.

Arm at Home

Instructions for arming the system when people are present at home.

Disarm

Procedure to deactivate the alarm system.

Cancel Alarm

Clearing the alarm memory and indicators after an event.

Emergency Alarm

Activating an emergency alarm state.

Receiving Alarm by Phone

How the system notifies users via phone calls during an alarm.

Remote Control

Using the remote control for system operations like arming and disarming.

Home Appliance Control

Managing connected home appliances remotely.

Home Appliance Switch Pairing

Procedure for pairing home appliance switches with the alarm unit.

Connect Wireless Siren (Option Function)

Instructions for connecting an optional wireless siren.

Pair the Siren

Procedure for pairing a wireless siren with the alarm unit.

Maintenance

System Test

Procedures for testing the main unit and sensors to ensure proper function.

Trouble Shooting

Guidance on diagnosing and resolving common system issues.

Standard Package