Dea Spazio 703 S - Page 16

S P A Z I O
Operatinginstructionsandwarnings
14
nowpositionthedoor/gateinitspositionofmax.opening.In
ordertodothis:
•• Setup and memorization of motor stroke
WARNINGDuringmotorsstrokememorisation,thecontrol
boarddetectsautomaticallythepresenceandtypeofphoto-
cells,safetydevicesandlimitswitcheswhichareinstalled.Itis
thereforeessentialthatduringthisphasethelatterbeproperly
connectedandworking.
Instruct. Function
Display
Manuallypositionthedoorinthehalfopenposition
thenpowerupthecontrolpanel,thepanelisnow
waitingforinstructions.
Scrolldowntheparametersuntilyouvisualizepro-
cedureP003
Confirm! The control board awaits a further
confirmation

Confermare tenendo premuto il tasto OK! until
APPR stops flashing: control panel isready to be
programmed.
Give aSTART impulse (by an alreadymemorised
remoteorakeypad):dooropens.
Once it arrives at desired opening point, give a
STARTinpulse:doorstops.Adjustthegreencamso
thatitpressestheopeninglimitswitch.
GiveaSTARTimpulse:doorcloses.
Onceitarrivesattheclosedposition,doorstops.
Adjusttheredcamsothatitpressestheclosingli-
mitswitches.Displaywillshow“----“,programming
complete.
•• Built-in radio receiver
DEAcontrolboardincludesa433,92MHzbuilt-inradioreceiver
acceptingbothtransmitterswithHCScoding(completerolling
codeorjustfixedpart),andHT12Edip-switchcoding.
•Thetypeofcodingis selectedby programmingthe working
parametern°8“typeofcoding”(seeTable2Parameters)
•Thereceivermemorycapacitycancontainupto100different
transmitters.
•When receiving a pulse from the transmitter, depending on
yourchannelselectionandlinking,thestartorthepedestrian/
closeinputsareactivated.Infact,byprogrammingoneofthe
workingparametersitispossibletochoose,accordingtoone’s
needs,whichkeyofthememorizedtransmitterswillactivate
thestartinputandwhichonewillactivatethepedestrianinput
(see“Channelselectionandlinkingonthetransmitter”).
•Whileyoumemorizeeachtransmitterthedisplayshowsapro-
gressive numberbywhich you willbeable to traceand,if
necessary,deleteeachtransmitterindividually
Instruct. Function
Display
Thecontrolboardisreadytoreceiveinstructions
Deletion of all transmitters
Scroll down the parameters until you visualize
P004
Confirm!Thecontrolboardawaitsafurther
confirmation

ConfirmbypressingontheOKkeyforafewsecon-
ds!Theprocedurestarts
Done!Thetransmittersmemoryhasbeendeleted
Scrolldowntheparametersuntilyouvisualize“----
”.Thecontrolboardawaitsfurtherinstructions
Memorization of transmitters
1
ScrolldowntheparametersuntilyouvisualizeP005
Confirm!Thereceiverentersinmemoriza-
tionmode.Theflashinglightturnson
Pressonanykeyofthetransmitter.
Memorization done! The flashing light
goes out for 2 seconds. The display vi-
sualizesthenumberofthetransmitterjust
memorized(es.“r001”)
Thereceiverrevertsautomaticallytomemori-
zationmode.Theflashinglightturnsonagain
Memorizeallnecessarytransmitters
Wait10secondsbeforequittingthememo-
rizationmode
Thereceiverwillnowreceiveallthememo-
rizedtransmitters
How to activate the memorization mode without
Operating on the control board
1
PresssimultaneouslyonkeyCH1andCH2,
oronthehiddenkeyofatransmitteralrea-
dymemorized
How to search and delete a transmitter
Scroll down the parameters until you visualize
P006
Confirm!Youcannowselectthetransmitter
Scroll down the transmitter numbers until
youreachthetransmittertobedeleted(eg.
“r003”)

ConfirmthedeletionbypressingtheOKkeyfora
fewseconds
OK!Thetransmitterisdeleted
Youcannowselecttheparameter
Scroll down the parameters until you visua-
lize “----”. The control board awaits further
instructions
1
Make sure that the receiver is set to receive the type of coding of the tran-
smitter you wish to memorize: visualize and, if necessary, update parameter
n° 8 “type of coding” (see “Personalization of working parameters “)
••
Channel selection and linking on the transmitter
The built-in receiver can control both the start input and the
pedestrian/closeone.Bysettingthecorrectvalueofthepara-
meter“P009Selectionandlinkingofchannels”itispossibleto
decidewhichkeyofthetransmitterwillactivateeachinput.
Ifyoucheckonthe“workingparameters”tableyouwillrealize
thattheP009parameterallowsyoutochooseamong16dif-
ferentcombinations.If,forinstance,youattributevalue“3”to
theparameterP009,allmemorizedtransmitterswillactivatethe
startinputthroughtheCH1andthepedestrianinputthrough
CH4.Pleaserefertochapter“Personalizationofworkingpara-
meters”inordertoselectyourowncombination..
•• Personalization of working parameters
Instruct. Function
Display
Thecontrolboardisreadytoreceiveinstructions
Scrolldownthe parametersuntilyouvisualizethe
oneyouwishtoset(ex.P010)
Confirm! The display shows the set parameter
value
Increaseordecreasethevalueuntilyoureachthe
valueyouwishtodefine
Confirm!Thedisplayshowsagaintheparameter
Scrolldowntheparametersuntilyouvisualise“----
”.Thecontrolboardawaitsfurtherinstructions
Theautomationisnowreadytoworkaccordingtothenewworking
parameters.
•• Resetting of default parameters (p.007)
DEAcontrolboardsoftwareincludesaresetproceduretore-
storedefaultvalues(theonesetbythemaker)ofallsettablepa-
rameters.Thevalueoriginallysetforeachparameterisshown
inthe“workingparameterstable”.Incaseyoushouldresetall