What to do if Dell B5460dn Mono Laser Printer says 'Imaging unit very low'?
If your Dell printer displays 'Imaging unit very low', you may need to replace the imaging unit very soon. If necessary, press to clear the message and continue printing.
How to fix 'Memory full' error on Dell printer?
If your Dell printer displays 'Memory full', you can press on the printer control panel to clear the message. You can also try decreasing the resolution setting or installing additional printer memory.
Why does my Dell B5460dn Mono Laser say 'Incorrect paper size'?
If your Dell printer is displaying 'Incorrect paper size', load the correct size of paper in the tray. Also, check the tray length and width guides to ensure the paper is loaded properly. Make sure the correct paper size and type are specified in Print Properties, the Print dialog, and the Paper menu on the printer control panel. If the MP Feeder Size is set to Universal, ensure the paper is large enough for the data being printed. Alternatively, you can press on the printer control panel to clear the message and print using a different tray, or cancel the print job.
What to do if Dell B5460dn Mono Laser Printer shows 'Check tray [x] connection'?
If your Dell printer displays 'Check tray [x] connection', try turning the printer off and then back on. If the error occurs again: 1. Turn off the printer. 2. Unplug the power cord. 3. Remove the specified tray. 4. Reattach the tray. 5. Connect the power cord. 6. Turn the printer back on. If the error persists, repeat steps 1-3, then contact technical support. You can also press to clear the message and continue printing.
What to do if Dell B5460dn Mono Laser Printer shows 'Incompatible output bin'?
If your Dell printer displays 'Incompatible output bin', remove the specified bin. Alternatively, press on the printer control panel to clear the message and continue printing without using the specified bin.
How to fix 'Disk must be formatted' error on Dell B5460dn Mono Laser?
If your Dell printer displays 'Disk must be formatted for use in this device', select Format disk from the printer control panel to format the printer hard disk and clear the message.
What to do if Dell B5460dn Mono Laser prompts to 'Change [paper source] to [custom string]'?
If your Dell printer displays 'Change [paper source] to [custom string] load [orientation]', load the correct size and type of paper in the tray, and then press on the printer control panel. Alternatively, you can cancel the print job.
What to do if Dell B5460dn Mono Laser Printer says 'Close door or insert cartridge'?
If your Dell printer displays 'Close door or insert cartridge', the toner cartridge may be missing or not installed properly. Insert the cartridge, and then close all doors and covers.
What to do if Dell Printer shows 'Defective flash detected'?
If your Dell printer displays 'Defective flash detected', replace the defective flash memory card. Alternatively, you can press on the printer control panel to ignore the message and continue printing, or cancel the current print job.
How to fix 'Disk full' error on Dell B5460dn Mono Laser Printer?
If your Dell printer displays 'Disk full', you can press on the printer control panel to clear the message and continue printing. You can also delete fonts, macros, and other data stored on the printer's hard disk, or install a printer hard disk with a larger capacity.
General| Print Technology | Laser |
|---|---|
| Print Resolution | 1200 x 1200 dpi |
| Standard Memory | 512 MB |
| Output Capacity | 500 sheets |
| Processor Speed | 800 MHz |
| Weight | 52.9 lbs |
| Monthly Duty Cycle | 275, 000 pages |
| Input Capacity | 650 sheets |
| Connectivity | USB 2.0, Ethernet |
| First Page Out Time | 4.4 seconds |
| Maximum Paper Size | A4, Legal |
| Operating System Compatibility | Windows, Linux, Mac OS |
| Duplex Printing | Standard |
To Next Page
