DeLonghi Eletta Automatic - Page 12

11
7.6 Auto-start
You can set the auto-start time in order to have the appliance
ready at a certain time (for example in the morning) so you can
make coee immediately.
Please note!
To enable this function, the time must already be set correctly.
To enable auto-start, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (g. 9) until “Auto-start” appears on
the display (B13);
3. Press the OK button (B12- g. 10). “Enable?” is displayed;
4. Press the OK button to conrm;
5. Press < or > to choose the hour;
6. Press the OK button to conrm;
7. Press < or > to change the minutes;
8. Press the OK button to conrm;
9. Press the MENU/ESC button to exit the menu.
Once the time has been conrmed, activation of auto-start is
indicated by the symbol displayed alongside the time.
To disable the function:
1. Select auto-start from the menu;
2. Press the OK button. “Disable?” is displayed;
3. Press the OK button to conrm.
The symbol is no longer displayed.
7.7 Auto-o (standby)
Auto-o can be set so that the appliance goes o after 15 or 30
minutes, or 1, 2 or 3 hours.
To programme Auto-o, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (g. 9) until “Auto-start” appears on
the display (B13);
3. Press the OK button (B12- g. 10);
4. Press < or > until the required operating time (15 or 30
minutes, or 1, 2 or 3 hours) is displayed;
5. Press the OK button to conrm;
6. Press the MENU/ESC button to exit the menu.
Auto-o is now programmed.
7.8 Cup warmer
This function enables the cup warmer to be enabled or disabled.
Proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (g. 9) until “Cup warmer” appears
on the display (B13);
3. Press the OK button (B12- g. 10). “Enable?” or “Disable?”
is displayed;
4. Press the OK button to enable or disable the cup warmer
(the message “Cup warmer Enabled” indicates that it is
active);
5. Press the MENU/ESC button to exit the menu.
Warming the cups keeps the coee hot.
7.9 Energy saving
Use this function to enable or disable energy saving. When en-
abled, the function reduces energy consumption in compliance
with European regulations.
To disable (or enable) energy saving, proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (g. 9) until “Energy Saving” appears
on the display (B13);
3. Press the OK button (B12- g. 10). “Disable?” is displayed
(or “Enable?” if the function has been disabled);
4. Press the OK button to disable (or enable) energy saving
mode;
5. Press the MENU/ESC button to exit the menu.
When the function is active, if the machine is not used for some
time, “Energy saving” is displayed.
Please note!
• When in energy saving mode, a few seconds elapse before
the rst coee, cappuccino or milk based coee is delivered
as the appliance must heat up again.
• To prepare any drink, press any button to exit energy sav-
ing, then press the button corresponding to the drink you
want to make.
• If the milk container is inserted, “Energy saving” is not
activated.
7.10 Setting the temperature
To modify the temperature of the water used to make the coee,
proceed as follows:
1. Press the MENU/ESC button (B14) to enter the menu;
2. Press < (B4) or > (B8) (g. 9) until “Set temperature” ap-
pears on the display (B13);
3. Press the OK button (B12- g. 10);
4. Press < or > until the required temperature is displayed
(●=low; ●●●●=maximum);
5. Press the OK button to conrm;
6. Press the MENU/ESC button to exit the menu.
7.11 Setting water hardness
For instructions on setting water hardness, see section “13.2
Setting water hardness”.