Warning
Please thoroughly read this instruction sheet before installation and putting it into use.
The content of this instruction sheet and the driver file may be revised without prior notice. Please consult
our distributors or download the most updated instruction/driver version at
http://www.delta.com.tw/product/em/control/cm/control_cm_main.asp
Introduction
IFD6500 is a convenient RS-485-to-USB converter, which does not require external power-supply
and complex setting process. It supports baud rate from 75 to 115.2kbps and auto switching direction
of data transmission. In addition, it adopts RJ-45 in RS-485 connector for users to wire conveniently.
And its tiny dimension, handy use of plug-and-play and hot-swap provide more conveniences for
connecting all DELTA IABU products to your PC.
Applicable Models: All DELTA IABU products.
Application & Dimension
Specifications
Power supply No external power is needed
Power consumption 0.4W
Isolated voltage 3,000V DC
Baud rate
75, 150, 300, 600, 1,200, 2,400, 4,800, 9,600, 19,200, 38,400, 57,600,
115,200 bps
RS-485 connector RJ-45
USB connector A type (plug)
Compatibility Full compliance with USB V2.0 specification
Max. cable length RS-485 Communication Port: 100 m
Support RS-485 half-duplex transmission
ENGLISH
RJ-45
PIN Description PIN Description
1 Reserved 5 SG-
2 Reserved
7 Reserved
4 SG+ 8 Reserved
Preparations before Driver Installation
Please extract the driver file (IFD6500_Drivers.exe) by following steps. You could find driver file
(IFD6500_Drivers.exe) in the CD supplied with IFD6500.
Note: DO NOT connect IFD6500 to PC before extracting the driver file.
STEP 1 STEP 2
STEP 3 STEP 4
STEP 5
You should have a folder marked SiLabs under drive C.
Driver Installation
After connecting IFD6500 to PC, please install driver by following steps.
LED Display
1. Steady Green LED ON: power is ON.
2. Blinking orange LED: data is transmitting.
注意事項
請詳細閱讀下列說明後才使用本產品，以確保使用安全。
由於產品精益求精，當內容規格或驅動程式有所修正時，請洽詢代理商或至台達網站
( http://www.delta.com.tw/product/em/control/cm/control_cm_main.asp )
下載最新版本。
產品簡介
IFD6500 RS-485/USB
轉換裝置，不需外接電源，不需任何設定，即可支援不同的傳輸速率從
75
到
115.2
kbps
，並可自動切換資料流方向。通過
USB
接口有隨插即用和熱插拔的方便性，提供和
RS-485
裝置
的溝通介面，體積小且方便使用，
RS485
採用
RJ-45
網路線接口，使用者能更便利的接線。
適用機種：台達電子
IABU
全系列產品。
產品應用及外觀尺寸
功能規格
電源需求
不需外接電源
消耗功率
0.4W
隔離電壓
3,000V DC
傳輸速度
75
、
150
、
300
、
600
、
1,200
、
2,400
、
4,800
、
9,600
、
19,200
、
38,400
、
57,600
、
115,200 bps
RS-485
端子形式
RJ-45
USB
接頭
A type (plug)
相容性
符合
USB V2.0
規格
最大使用線長
RS-485
通訊埠：
100
公尺
支援
RS-485
半雙工
繁體中文
RJ-45
PIN
說明
To Next Page
Need help?
General
