Wiring:
Type Wire gauge (AWG) Stripped length Torque
Solid
24 - 12
7 - 8 mm
(0.28 - 0.31 inches)
5 kg-cm (4.3 lb-in)
Stranded
24 - 12
7 - 8 mm
(0.28 - 0.31 inches)
5 kg-cm (4.3 lb-in)
Please refer to the following diagram when wiring the power connector. The temperature
rating of the cable must be greater than 75°C (167°F).
(6) Hardware specifications
Model DOP-110IG
Display
Panel type
10.4” TFT LCD (65536 colors)
Resolution
800 x 600 pixels
Backlight LED backlight
(half-life under room temperature 25°C > 10,000 hours)
*1
Display range 211.2 x 158.4 mm
Brightness 300 cd / m² (Typ.)
CPU ARM Cortex-A8 (800 MHz)
Flash ROM
256 Mbytes
RAM
256 Mbytes
Touchscreen 4-wire resistive touchscreen > 10,000,000 operated
Audio
output
Buzzer
Multi-Tone Frequency (2 - 4 kHz) / 80 dB
AUX Stereo output
Network interface
1-port 10/100 Mbps auto-detection
(with built-in isolated power circuit)
*2
USB 1 USB Slave Ver 2.0; 1 USB Host Ver 2.0
SD SD card (supports SDHC)
Serial
communication
port
COM1 RS-232 (supports hardware flow control)
*2
COM2 RS-232 / RS-422 / RS-485
*2
COM3
RS-232 / RS-422 / RS-485
*2
Auxiliary function key
N/A
Calendar Built-in
Cooling method Natural cooling
Approvals
CE / UL (please use shielding network cable and magnetic ring with the
filter of 300 ohm / 100 MHz)
Panel waterproof level IP65 / NEMA4
Operation voltage
*2
DC +24V (-15% to +15%) (please use an isolated power supply)
Supplied by Class 2 or SELV circuit (isolated from MAINS by double insulation)
Leakage current 500 V
AC
for 1 minute (between DC24V terminal and FG terminal)
Power consumption
*3
9.6 W (Max.)
*3
Backup battery 3V lithium battery CR2032 x 1
Backup battery life
About 3 years or more at 25°C (77°F)
(subject to operation temperature and condition)
Operation temperature 0°C to 50°C (32°F to 122°F)
Storage temperature
-20°C to +60
°
C (-4°F to 140°F)
Operating environment
10% to 90% RH [0°C to 40°C (32°F to 104°F)];
10% to 55% RH [41°C to 50°C (105.8°F to 122°F)];
pollution degree: 2
Model DOP-110IG
Vibration resistance
Conforms to IEC61131-2: continuous vibration 5 Hz - 8.3 Hz with amplitude
3.5 mm; 8.3 Hz - 150 Hz with amplitude 1G
Shock resistance
Conforms to IEC60068-2-27: 11 ms, 15 G Peak, in X, Y, Z directions
each for 6 times
Dimensions
(W) x (H) x (D) mm
299 x 224 x 46.8
Mounting dimensions
(W) x (H) mm
285.2 x 210.2
Weight Approx.1600 g
Note:
1. The half-life of the backlight is defined as the maximum luminance being reduced by 50% when the maximum drive
current is supplied to the HMI. The life of LED backlight shown here is estimated at the room temperature of 25°C
(77°F) with ambient humidity.
2. The withstand voltage of the isolated power circuit is 1500 V peak for 1 minute.
3. The HMI power consumption is the power consumed when the HMI is not connecting with other peripheral devices.
To ensure normal operation of the HMI, the recommended capacity of the power supply is 1.5 to 2 times of the
specified power consumption.
4. Isolated power supply is recommended.
5. For the programming software DOPSoft of DOP-100 series and its user manual, you can download them at
http://www.delta.com.tw/ia.
6. DOP-100 series can be used with other industrial automation equipment. Please read through this sheet carefully
and install the product according to the instructions to avoid danger.
To Next Page
Loading...