Why do changes not take effect on my Delta enteliZONE eZNT-Wi Thermostat?
To ensure changes take effect on your Delta Thermostat, click the Save button located in the top right of the Configuration page. Also, ensure that more than one device is not connected at a time.
How to recover from incorrect configuration on Delta enteliZONE eZNT-Wi?
To recover from an incorrect configuration on your Delta Thermostat, verify the SSID and password for your router. Sometimes a Run/Clear procedure must be done to return the database to the factory default and also to remove any retained network settings information.
How to return Delta enteliZONE eZNT-Wi Thermostat to factory default settings?
To return your Delta Thermostat to factory default settings, open the thermostat and put the Run/Clear jumper into the Clear position for 10 seconds.
How to set time on Delta Wi-Fi thermostat?
To set the time on your Delta Wi-Fi thermostat, select the Wi-Fi thermostat in enteliWEB and execute the Set Time command.
What to do if I cannot get the configuration webpage for a specific Delta Wi-Fi thermostat?
If you cannot get the configuration webpage for your Delta Wi-Fi thermostat, verify that you do not have an active internet connection. If you are doing an internal setup, ensure that there is no unintended external connection.
What to do if the Delta Thermostat configuration webpage does not accept the Keypad Password in the Device Info section?
If the configuration webpage for your Delta Thermostat does not accept the Keypad Password in the Device Info section, confirm that you have entered the correct password. It is possible that the password was changed from the default value.
Why my Wi-Fi settings changes were not implemented on Delta enteliZONE eZNT-Wi Thermostat?
If your Wi-Fi settings changes were not implemented on your Delta Thermostat, make the changes and then click Save.
Why webpage Password change does not take effect on Delta enteliZONE eZNT-Wi?
If the webpage password change does not take effect on your Delta Thermostat, save and also execute Commit. Passwords must be alphanumeric and contain no symbols. You may need to reset the thermostat for the changes to take effect.
What to do if I cannot see any eZNT- Wi/ eZNTW units during initial AP (Host) mode on Delta enteliZONE eZNT-Wi?
If you cannot see any eZNT- Wi/ eZNTW units during initial AP (Host) mode on your Delta Thermostat, connect under Station Mode IP. In Station mode, the Wi-Fi thermostats are visible in enteliWEB.
How to clear the database but keep the network settings on Delta enteliZONE eZNT-Wi?
To clear the database but keep the network settings on your Delta Thermostat, save the database and then use the Clear Database command from enteliWEB.
General| Model | eZNT-Wi Series |
|---|---|
| Type | Thermostat |
| Connectivity | Wi-Fi |
| Display | LCD |
| Power Supply | 24 VAC |
| Operating Temperature | 0°C to 50°C |
| Humidity Range | 5% to 95% non-condensing |
| Weight | 150 g |
| Certifications | CE, FCC, UL |
Details the eZNT-Wi as a BACnet/IP wireless Wi-Fi product with local I/O.
Lists essential passwords for Wi-Fi configuration.
Explains Wi-Fi concepts specific to eZNT-Wi/eZNTW-Wi.
Details default MAC addresses for Wi-Fi devices.
Explains the AP Host Mode (IPS2) for Wi-Fi.
Explains the Station Client Mode (IPS1) for Wi-Fi.
Configuring Wi-Fi using NFC and Net Builder app.
Configuring Wi-Fi via the built-in webserver.
Configuring Wi-Fi settings using enteliWEB.
Solutions for common Wi-Fi problems.
How to navigate and configure using the on-screen menu.
Restoring default factory settings using the RUN/CLEAR jumper.
How to tap and read configuration data via NFC.
Writing device settings using the Stat Configurator app.
Procedures for manual calibration of the CO2 sensor.
Calibrating the CO2 sensor via the on-screen menu.
Calibrating the CO2 sensor using enteliWEB/ORCAview.
Auto-calibrating the CO2 sensor via the on-screen menu.
Installing Delta eZNx driver to create a virtual COM port.
To Next Page
