EasyManuals Logo

Denon AVR-X3600H User Manual

Denon AVR-X3600H
310 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #255 background imageLoading...
Page #255 background image
Desired sound does not come out
The volume does not increase.
0
The maximum volume is set too low. Set the maximum volume using “Limit” on the menu. (v p. 173)
0
Appropriate volume correction processing is performed according to the input audio format and settings, so the volume may not reach the upper limit.
No sound comes out with the HDMI connection.
0
Check the connection of the HDMI connectors. (v p. 64)
0
When outputting HDMI audio from the speakers, set “HDMI Audio Out” on the menu to “AVR”. To output from the TV, set “TV”. (v p. 181)
0
When using the HDMI Control function, check that the audio output is set to the AV amplifier on the TV. (v p. 142)
When an eARC function-compatible television is connected, television audio is not output from the speaker connected to this unit
0
eARC function settings may be required depending on the eARC function-compatible television you are using. Make sure eARC is set to on if this
setting exists on your television. For more information, check your television’s owner’s manual.
0
Make sure the input source of this unit is “TV Audio”.
0
The eARC function does not operate when the HDMI input connector is set to the “TV Audio” input source. To enable eARC function operation, remove
the HDMI input connector setting, then restart this unit and the television. (v p. 194)
No sound comes out of a specific speaker.
0
Check that speaker cables are properly connected.
0
Check that a selection other than “None” is set for the “Speaker Config.” setting in menu. (v p. 214)
0
Check the “Assign Mode” setting in the menu. (v p. 208)
0
When the sound mode is “Stereo” and “Virtual”, audio is only output from the front speakers and subwoofer.
0
Audio is not output from the surround back speaker if “Speaker Virtualizer” is set to “On” when “Speaker Config.” - “Surr. Back” is set to “1 spkr” in the
menu. (v p. 167)
0
When “Speaker Config.” - “Surr. Back” is set to “2 spkrs”, “Speaker Config.” - “Center” is set to “Large” or “Small”, and sound mode is set to “IMAX
DTS”, surround audio is output from the surround back speaker. Audio is not output from the surround speaker. (v p. 216)
Contents
Connections Playback Settings Tips Appendix
255
Front panel Display Rear panel Remote Index

Other manuals for Denon AVR-X3600H

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Denon AVR-X3600H and is the answer not in the manual?

Denon AVR-X3600H Specifications

General IconGeneral
Receiver typeSurround
Frequency range20 - 20000 Hz
Pre-out channels11.2
Pre-out connectivityYes
Audio output channels9.2 channels
Dynamic power per channel (6 Ohm)180 W
Power output per channel (20-20KHz@8 Ohm)105 W
Display-
HDCP version2.2
Apple dockingNo
Product colorBlack
Audio decodersDTS-HD Master Audio, Dolby Atmos, Dolby Surround, Dolby TrueHD
Audio formats supportedAAC, ALAC, FLAC, MP3, WAV, WMA
Supported radio bandsAM, FM
Internet radio services supportedAmazon Music, Deezer, Pandora, Spotify, Tidal, TuneIn
HDMI in8
Composite video in3
Ethernet LAN (RJ-45) ports1
Component video (YPbPr/YCbCr) in2
Supported video modes480i, 576i
Power consumption (standby)0.1 W
Power consumption (typical)600 W
Package weight14600 g
Cables includedAC
Speakers connectivity typeBinding post
Weight and Dimensions IconWeight and Dimensions
Depth379 mm
Width434 mm
Height167 mm
Weight12100 g

Related product manuals