Denon AVR-X4800H User Manual

z1
During playback in Pure Direct mode, the surround parameters are the same as in Direct mode.
z2
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD or Dolby Atmos signal is played.
z3
This item can be selected when a Dolby Digital, Dolby Digital Plus, Dolby TrueHD, Dolby Atmos, DTS:X or DTS signal is played.
z4
This item can be selected when a DTS:X signal that is compatible with the Dialog Control function is input.
z5
This item can be selected when a Dolby Digital or DTS signal or DVD-Audio is played.
z6
This item can be selected when Height, Ceiling or Dolby Atmos Enabled speakers are used.
z7 This item cannot be set when “Dynamic EQ” is set to “On”. (v
p. 191)
z8 This item cannot be set when “Center” is set to “None”. (v p. 233)
z9 This item cannot be set when “Subwoofer” in the menu is set to “None”. (v
p. 233)
z10
This item cannot be set when Audyssey
®
Setup (Speaker Calibration) has not been performed.
z11
This item cannot be selected when a DTS:X format with a sampling frequency of over 48 kHz is input.
z12
This item cannot be set when “MultEQ
®
XT32” in the menu is set to “Off”. (v p. 190)
z13
This item cannot be set when sound mode is “DTS Virtual:X” or sound mode that have “+Virtual:X” in the sound mode name.
z14
This item can be set when the input signal is analog, PCM 48 kHz or 44.1 kHz.
z15
This can be set when the LFE signal is included in the input signal.
z16 This setting is available when “Subwoofer Mode” in the menu is set to “LFE+Main”. (v
p. 241)
z17 This item can be set when “Front” is set to “Small” or “Subwoofer Mode” is set to “LFE+Main”. (v
p. 233, 241)
z18
This can be set if the input signal does not contain an Auro-3D signal or if the input Auro-3D signal does not contain Front Height channels.
Contents
Connections Playback Settings Tips Appendix
314
Front panel Display Rear panel Remote Index

Denon AVR-X4800H Specifications

General

Channels	9.4
Dolby Atmos	Yes
DTS:X	Yes
HDMI Inputs	7
HDMI Outputs	3
4K/120Hz Pass-through	Yes
8K Support	Yes
Wi-Fi	Yes (2.4GHz/5GHz)
Bluetooth	Yes
HEOS Built-in	Yes
Amplifier Channels	9
Power Output per Channel @ 8 Ohms / 1 kHz / 0.08% THD / 2 Channels Driven	125W
Speaker Impedance	4-16 Ohms
Auro 3D	Yes
IMAX Enhanced	Yes
HDCP Support	2.3
HDR Compatibility	HDR10, HDR10+, Dolby Vision, HLG
eARC Support	Yes
Phono Input	Yes
Ethernet	Yes
Voice Assistant Support	Amazon Alexa, Google Assistant, Apple Siri
Audyssey MultEQ XT32	Yes
Total Harmonic Distortion	0.05%
Input Sensitivity/Impedance	200 mV / 47 kOhms
Network Connectivity	Ethernet, Wi-Fi
Supported Audio Formats	MP3, WMA, AAC, FLAC, ALAC, WAV, DSD
Dimensions (W x H x D)	434 x 167 x 389 mm
Weight	13.5 kg
Power Output per Channel	125W
Voice Control	Yes
Frequency Response	10 Hz - 100 kHz
DAC	32-bit AKM
Video Pass-Through	8K
Zone Audio Output	Zone 2, Zone 3
Wireless Audio Streaming	Yes
Signal-to-Noise Ratio	102 dB
Video Inputs/Outputs	7/3 (HDMI)
Audio Inputs/Outputs	7 HDMI inputs, 3 HDMI outputs, 1 phono input, 2 optical inputs, 1 coaxial input