Name: DEUTSCHMANN AUTOMATION LOCON 15 Series
Brand: DEUTSCHMANN AUTOMATION
Rating: 4 (1 reviews)

To Next Page

Instruction manual

Electronic cam control

LOCON 24, 48, 64, LTC

Display- and operating unit

TERM 24 and TERM 6

Deutschmann Automation GmbH & Co. KG

Carl-Zeiss-Str. 8 D-65520 Bad Camberg  +49-

(0)6434 / 9433-0  +49-(0)6434 / 9433-40

eMail: mail@deutschmann.de Internet: http://www.deutschmann.com

Default Chapter5
- Table of Contents5
1 Introduction11
- On this Manual11
- From the Mechanical System to an Electronic System12
- Deutschmann Automation's Range of Products12
2 EMC Directives for Products of DEUTSCHMANN AUTOMATION13
3 Electrical Connections LOCON 24, 48, 6414
- Rear View LOCON 24, 48, 6414
- Pin Assignment LOCON 24, 48, 6415
- Signal Description LOCON 24, 48, 6418
  - Status Leds19
    - Front View19
    - Rear View19
- External Program Selection19
- Installation and Commissioning of LOCON 24, 48 and 6420
4 Basic Unit TERM 24, LOCON 24, 48 and 6423
- Front View23
  - Version IP 5424
  - Version IP 6524
5 Mechanical Installation Instructions TERM 24, LOCON24
- PM-Version24
- Dimensional Drawings25
6 Electrical Connections TERM 2429
- Pin Assignment X1 TERM 24 (5-Pin Screw-Type Plug Connector)29
- Installation and Commissioning of the TERM 2429
7 LOCON 24, 48 and 64 Options30
- Expansion to 32 Outputs (LOCON 24 Only)30
- Inputs and Logic Functions (LOCON 24 and 48 Only)30
- SSI Interface30
- Incremental Encoder; Incremental Counting/Direction Inputs30
- Encoder Monitoring (Option G)30
- Speed Display31
- Direction-Cams31
- Angle-Time Cam32
- Memory Expansion32
- Offline Programming32
- Data Backup and Documentation on PC33
- Lockable Outputs33
- Program Controller Function (Encoder Simulation)33
- Analog Outputs33
- Option X37 - Encoder Monitoring34
- Option H08 - Highspeed-Idle Time Compensation34
- Option X53 (Preset Value)34
- Option X55 (Locked Outputs)34
- Option X59 (Braking Angle Display)35
- Option X81 (24 Bit SSI-Encoder)35
- Special Versions35
8 LOCON LTC (Special Version)36
- Mechanics Space Requirements36
- Electrical Connections37
- Programming of the Cams40
- Function "Apprentissage41
  - Presentation41
  - Starting the Function "Apprentissage41
- Control42
9 Networking Terminals with Cam Controls and Pcs47
- RS232 Link47
- RS485 Link (DICNET)47
- Cable Type for DICNET47
  - Earthing, Shielding48
  - Line Termination at DICNET48
- Comparison DICNET® - RS23248
- Connection Examples49
10 LOCON 24 with Profibus and MPI52
11 Commissioning and Self-Test53
- Commissioning of the Terminal53
  - Self-Test of the Terminal53
- Commissioning of the Cam Control53
  - Self-Test of the Cam Control54
12 Brief Instructions TERM 24 / LOCON 24, 48, 6455
13 Operation LOCON 24, 48, 6457
- Main Menu LOCON 24, 48, 6457
  - Programming Enable (Dongle)57
  - Function, Program Controller57
- Configuration and Initialisation57
  - LOCON 24, 48 and 64 Parameter Table58
- Locon 24 Mt58
  - Parameter Description59
14 Operation Via TERM 2462
- Fundamentals on TERM 24 and LOCON 24, 48 and 6462
- Main Menu TERM 2462
- Programming Via TERM 2464
- Initialisation72
- Configuration74
- Logic Functions76
- Locked Outputs81
- Function Speed Limit Value81
15 Basic Device TERM 6 (External Operating Unit)82
- Assembly of the Instrument82
- View TERM 682
- Technical Dimensional Drawings83
- Pin Assignment TERM 686
  - Interface Switch-Over86
- Programming of Several Devices with TERM 686
  - Selecting the Device Number on TERM 686
- Display of the Executed Program Via TERM 687
- Reading and Changing Cam Control Parameters87
- Programming Angle-Time-Cams Via TERM 687
16 Technical Details88
- Technical Data TERM 2488
- Technical Data LOCON 2489
- Technical Data LOCON 4890
- Technical Data LOCON 6491
- LOCON 24, LOCON 48 and LOCON 64 Memory Expansion92
- Specification of the Input Levels92
- Specification of the Output Drivers92
- 16.8 Switching Accuracy of the Deutschmann Cam Controls92
  - Timing Diagram94
- Function of the Idle-Time Compensation94
- 16.10 Environmental Specifications of Cam Controls of the LOCON Series95
- 16.11 Dicnet95
- 16.12 Communication Interface96
- 16.13 Coding Device Numbers97
17 Error Messages98
- Error Number 198
- Error Number 2098
- Error Number 100100
- Error Number 200-299 (Terminal Error)101
18 Order Code102
- TERM 24 Terminal102
- LOCON 24, 48 and 64 Cam Controls102
  - Explanation of the Order Designation102
- Order Designation Examples103
- Standard Accessory103
  - Standard Accessory of LOCON 24, 48, 64 and TERM 24103
19 Servicing104
- Returning a Unit104
- Internet104
20 Appendix105
- Description and Connection of the DICNET®-Adapter105
  - DICNET®-Adapter DICADAP 3105

Questions and Answers:

Need help?

Do you have a question about the DEUTSCHMANN AUTOMATION LOCON 15 Series and is the answer not in the manual?

DEUTSCHMANN AUTOMATION LOCON 15 Series Specifications

General

Brand	DEUTSCHMANN AUTOMATION
Model	LOCON 15 Series
Category	Industrial Electrical
Language	English

Related product manuals

DEUTSCHMANN AUTOMATION LOCON 24

106 pages

DEUTSCHMANN AUTOMATION LOCON 15 Series User Manual

Table of Contents

Questions and Answers:

DEUTSCHMANN AUTOMATION LOCON 15 Series Specifications

Related product manuals