DEUTSCHMANN AUTOMATION LOCON 24

To Next Page

Instruction manual

Electronic cam control

LOCON 24, 48, 64, LTC

Display- and operating unit

TERM 24 and TERM 6

Deutschmann Automation GmbH & Co. KG

Carl-Zeiss-Str. 8 D-65520 Bad Camberg  +49-

(0)6434 / 9433-0  +49-(0)6434 / 9433-40

eMail: mail@deutschmann.de Internet: http://www.deutschmann.com

Main Page

Default Chapter5
- Table of Contents5
1 Introduction11
- On this Manual11
- From the Mechanical System to an Electronic System12
- Deutschmann Automation's Range of Products12
2 EMC Directives for Products of DEUTSCHMANN AUTOMATION13
3 Electrical Connections LOCON 24, 48, 6414
- Rear View LOCON 24, 48, 6414
- Pin Assignment LOCON 24, 48, 6415
- Signal Description LOCON 24, 48, 6418
  - Status Leds19
    - Front View19
    - Rear View19
- External Program Selection19
- Installation and Commissioning of LOCON 24, 48 and 6420
4 Basic Unit TERM 24, LOCON 24, 48 and 6423
- Front View23
  - Version IP 5424
  - Version IP 6524
5 Mechanical Installation Instructions TERM 24, LOCON24
- PM-Version24
- Dimensional Drawings25
6 Electrical Connections TERM 2429
- Pin Assignment X1 TERM 24 (5-Pin Screw-Type Plug Connector)29
- Installation and Commissioning of the TERM 2429
7 LOCON 24, 48 and 64 Options30
- Expansion to 32 Outputs (LOCON 24 Only)30
- Inputs and Logic Functions (LOCON 24 and 48 Only)30
- SSI Interface30
- Incremental Encoder; Incremental Counting/Direction Inputs30
- Encoder Monitoring (Option G)30
- Speed Display31
- Direction-Cams31
- Angle-Time Cam32
- Memory Expansion32
- Offline Programming32
- Data Backup and Documentation on PC33
- Lockable Outputs33
- Program Controller Function (Encoder Simulation)33
- Analog Outputs33
- Option X37 - Encoder Monitoring34
- Option H08 - Highspeed-Idle Time Compensation34
- Option X53 (Preset Value)34
- Option X55 (Locked Outputs)34
- Option X59 (Braking Angle Display)35
- Option X81 (24 Bit SSI-Encoder)35
- Special Versions35
8 LOCON LTC (Special Version)36
- Mechanics Space Requirements36
- Electrical Connections37
- Programming of the Cams40
- Function "Apprentissage41
  - Presentation41
  - Starting the Function "Apprentissage41
- Control42
9 Networking Terminals with Cam Controls and Pcs47
- RS232 Link47
- RS485 Link (DICNET)47
- Cable Type for DICNET47
  - Earthing, Shielding48
  - Line Termination at DICNET48
- Comparison DICNET® - RS23248
- Connection Examples49
10 LOCON 24 with Profibus and MPI52
11 Commissioning and Self-Test53
- Commissioning of the Terminal53
  - Self-Test of the Terminal53
- Commissioning of the Cam Control53
  - Self-Test of the Cam Control54
12 Brief Instructions TERM 24 / LOCON 24, 48, 6455
13 Operation LOCON 24, 48, 6457
- Main Menu LOCON 24, 48, 6457
  - Programming Enable (Dongle)57
  - Function, Program Controller57
- Configuration and Initialisation57
  - LOCON 24, 48 and 64 Parameter Table58
- Locon 24 Mt58
  - Parameter Description59
14 Operation Via TERM 2462
- Fundamentals on TERM 24 and LOCON 24, 48 and 6462
- Main Menu TERM 2462
- Programming Via TERM 2464
- Initialisation72
- Configuration74
- Logic Functions76
- Locked Outputs81
- Function Speed Limit Value81
15 Basic Device TERM 6 (External Operating Unit)82
- Assembly of the Instrument82
- View TERM 682
- Technical Dimensional Drawings83
- Pin Assignment TERM 686
  - Interface Switch-Over86
- Programming of Several Devices with TERM 686
  - Selecting the Device Number on TERM 686
- Display of the Executed Program Via TERM 687
- Reading and Changing Cam Control Parameters87
- Programming Angle-Time-Cams Via TERM 687
16 Technical Details88
- Technical Data TERM 2488
- Technical Data LOCON 2489
- Technical Data LOCON 4890
- Technical Data LOCON 6491
- LOCON 24, LOCON 48 and LOCON 64 Memory Expansion92
- Specification of the Input Levels92
- Specification of the Output Drivers92
- 16.8 Switching Accuracy of the Deutschmann Cam Controls92
  - Timing Diagram94
- Function of the Idle-Time Compensation94
- 16.10 Environmental Specifications of Cam Controls of the LOCON Series95
- 16.11 Dicnet95
- 16.12 Communication Interface96
- 16.13 Coding Device Numbers97
17 Error Messages98
- Error Number 198
- Error Number 2098
- Error Number 100100
- Error Number 200-299 (Terminal Error)101
18 Order Code102
- TERM 24 Terminal102
- LOCON 24, 48 and 64 Cam Controls102
  - Explanation of the Order Designation102
- Order Designation Examples103
- Standard Accessory103
  - Standard Accessory of LOCON 24, 48, 64 and TERM 24103
19 Servicing104
- Returning a Unit104
- Internet104
20 Appendix105
- Description and Connection of the DICNET®-Adapter105
  - DICNET®-Adapter DICADAP 3105

Need help?

Do you have a question about the DEUTSCHMANN AUTOMATION LOCON 24 and is the answer not in the manual?

DEUTSCHMANN AUTOMATION LOCON 24 Specifications

General

Type	LOCON 24
Supply Voltage	24 V DC
Operating Temperature	-20°C to +70°C
CAN Interface	Yes
Isolation Voltage	500 V
Housing Material	Plastic
Protection Class	IP20
Connection Type	Screw terminals
Current Consumption	100 mA
Baud Rate	Up to 1 Mbit/s

Related product manuals

LOCON 15 Series

66 pages

DEUTSCHMANN AUTOMATION LOCON 24 - User Manual

Table of Contents

DEUTSCHMANN AUTOMATION LOCON 24 Specifications

Related product manuals