DeWalt DCD200 - Residual Risks; Important Safety Instructions for All Battery Chargers

6
ENGLISH
• Connect the brown lead to the live terminal in theplug.
• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the
earthterminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1mm
2
; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to TechnicalData).
• Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
batterypack.

WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,
charge only
DeWALT
rechargeable batteries. Other types of
batteries may burst causing personal injury anddamage.

CAUTION: Children should be supervised to ensure that
they do not play with theappliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting toclean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to worktogether.
• These chargers are not intended for any uses other than
charging
DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock orelectrocution.
• Do not expose charger to rain orsnow.
• Pull by plug rather than cord when disconnecting
charger. This will reduce risk ofdamage to electric plug
andcord.
• Make sure that cord is located so that it will not be
stepped on, tripped over, or otherwise subjected to
damage orstress.
Chargers
DeWALT
chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
Your
DeWALT
charger is double insulated in
accordance with EN60335; therefore no earth wire
isrequired.
If the supply cord is damaged, it must be replaced only by
DeWALT
or an authorised serviceorganisation.
Mains Plug Replacement
(U.K.& Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the oldplug.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot
duringoperation.
• Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
Additional Safety Rules for Drain Cleaner
• Stop the tool immediately if the cable binds and stops. The
cable can twist, kink or break ifoverstressed.
• Inspect cable for wear and damage beforeuse.
• If the cable is worn or damaged, replace the cable before using
the drain cleaner. Refer to OptionalAccessories.
• Do not twist, kink or over bend cables. A broken cable may
result in serious personalinjury.
• The drain cleaning process can damage floors and other
surfaces and can bemessy. Use appropriate protective covers
to prevent damage and hazards to surroundingarea. The
front of the drain cleaner should be no farther than 15cm
from drain opening. If not possible, use additional pipe and
fittings to extend the drain. Exposing more than 15cm of cable
can cause twisting, kinking, breaking or whipping of thecable.
• This tool is intended to be used by a single operator, so that
they alone are able to control feed and rotation of the cable.
If the cable stops rotating, the user must immediately release
the trigger to prevent twisting, kinking, breaking or whipping
of thecable.
• Operate the drain cleaner in reverse rotation only as described
in this manual. Running the tool in reverse for extended
periods can cause damage to thecable.
• Do not pull the trigger with the end of the cable outside of
thepipe