DeWalt DCF883M2 Original Instructions

English
6
resulting in personal injury and property
damage.
CAUTION: Children should be
supervised to ensure that they do not
play with the appliance.
NOTICE: Under certain conditions, with
the charger plugged in to the power
supply, the exposed charging contacts
inside the charger can be shorted by
foreign material. Foreign materials of
a conductive nature such as, but not
limited to, steel wool, aluminum foil or
any buildup of metallic particles should
be kept away from charger cavities.
Always unplug the charger from the
power supply when there is no battery
pack in the cavity. Unplug charger
before attempting to clean.
 • DONOTattempttochargethebatterypack
with any chargers other than the ones in
this manual. The charger and battery pack are
specifically designed to work together.
 • Thesechargersarenotintendedfor
any uses other than charging
DeWALT
rechargeable batteries. Any other uses
may result in risk of fire, electric shock or
electrocution.
 • Donotexposechargertorainorsnow.
 • Pullbyplugratherthancordwhen
disconnecting charger. This will reduce risk
of damage to electric plug and cord.
 • Makesurethatcordislocatedsothatitwill
not be stepped on, tripped over or otherwise
subjected to damage or stress.
 • Donotuseanextensioncordunlessit
is absolutely necessary. Use of improper
extension cord could result in risk of fire,
electric shock or electrocution.
 • When operating a charger outdoors, always
provide a dry location and use an extension
cord suitable for outdoor use. Use of a cord
suitable for outdoor use reduces the risk of
electric shock.
 • Donotblocktheventilationslotsonthe
charger.Theventilationslotsarelocated
on the top and sides of the charger. Place
the charger in a position away from any heat
source.
 • Donotoperatechargerwithdamagedcord
or plug — have them replaced immediately.
 • Do not operate charger if it has received
a sharp blow, been dropped or otherwise
damaged in any way. Take it to an authorised
service centre.
 • Donotdisassemblethecharger;takeitto
an authorised service centre when service or
repair is required. Incorrect reassembly may
result in a risk of electric shock, electrocution or
fire.
 • Incaseofdamagedpowersupplycordthe
supply cord must be replaced immediately by
the manufacturer, its service agent or similar
qualified person to prevent any hazard.
 • Disconnectthechargerfromtheoutlet
beforeattemptinganycleaning.Thiswill
reduce the risk of electric shock. Removing
the battery pack will not reduce this risk.
• NEVERattempt to connect 2 chargers together.
 • Thechargerisdesignedtooperateon
standard220-240Vhouseholdelectrical
power. Do not attempt to use it on any other
voltage. This does not apply to the vehicular
charger.
Save tHeSe inStructionS
Chargers
The DCB105 charger accepts 10.8 V, 14.4 V and
18 V Li-Ion (DCB121, DCB123, DCB140, DCB141,
DCB142, DCB180, DCB181 and DCB182) battery
packs.
This charger requires no adjustment and is designed
to be as easy as possible to operate.
Charging Procedure (fig. 2)
1. Plug the charger into an appropriate 220-240 V
outlet before inserting the battery pack.
2. Insert the battery pack (f) into the charger,
making sure the pack is fully seated in the
charger. The red (charging) light will blink
continuously indicating that the charging
process has started.
3. The completion of charge will be indicated by
the red light remaining ON continuously. The
pack is fully charged and may be used at this
time or left in the charger.
NOTE: To ensure maximum performance and life of
Li-Ion batteries, fully charge the pack before first use.

DeWalt DCF883M2 Specifications

General

Brand	DeWalt
Model	DCF883M2
Category	Impact Driver
Language	English