DeWalt DCMPH566 User Manual

14
ENGLISH
Optional Accessories

WARNING: Since accessories, other than those offered
by DeWALT, have not been tested with this product, use
of such accessories with this tool could be hazardous.
To reduce the risk of injury, only
DeWALT recommended
accessories should be used with thisproduct.
Consult your dealer for further information on the
appropriateaccessories.
Cleaning

WARNING: Blow dirt and dust out of the main housing
with dry air as often as dirt is seen collecting in and around
the air vents. Wear approved eye protection and approved
dust mask when performing thisprocedure.

WARNING: Never use solvents or other harsh chemicals
for cleaning the non-metallic parts of the tool. These
chemicals may weaken the materials used in these parts.
Use a cloth dampened only with water and mild soap.
Never let any liquid get inside the tool; never immerse any
part of the tool into aliquid.
Lubrication (Fig.A)
Blades
1. After use, carefully clean the blade
11
with a resinsolvent.
2. After cleaning, apply a light film of lubrication to the
exposedblade.
3. Turn the trimmer vertical with the blades toward the ground
and run the trimmer for a few seconds to fully disperse
thelubrication.
Maintaining Blade (Fig. M)
The cutting blades are made from high quality, hardened steel
and with normal usage, they will not require resharpening.
However, if you accidentally hit a wire fence, stones, glass, or
other hard objects as shown in Fig. M you may put a nick in the
blade. There is no need to remove this nick as long as it does not
interfere with the movement of the blade. If it does interfere,
remove the battery and use a fine toothed file or sharpening
stone to remove the nick. If you drop the trimmer, carefully
inspect it for damage. If the blade is bent, housing cracked,
handles broken or if you see any other condition that may affect
the trimmer’s operation contact your local D
eWALT authorised
service centre for repairs before putting it back intouse.
Lubrication
Your power tool requires no additionallubrication.
MAINTENANCE
Your power tool has been designed to operate over a long
period of time with a minimum of maintenance. Continuous
satisfactory operation depends upon proper tool care and
regularcleaning.

WARNING:To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
The charger and battery pack are notserviceable.
SIDE TRIMMING HEDGES (Fig.L) – Orient the trimmer
as shown and begin at the bottom and sweepup.
Guidelines for trimming (Australia & New
Zealand)
• Trim hedges and shrubs with seasonal leaves (new leaves
every year) in December andMarch.
• Trim evergreens in September andFebruary.
•
Trim conifers and other fast growing shrubs every six weeks
from October untilMarch.
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals. Do not store the unit
on or adjacent to fertilizers orchemicals.
With the battery removed, use only mild soap and a damp
cloth to clean the unit. Never let any liquid get inside the unit;
never immerse any part of the unit into a liquid. Prevent the
blades from rusting by applying a film of light machine oil
aftercleaning.
Blade Sharpening (Fig. N)
• KEEP BLADE SHARP FOR BEST PERFORMANCE. A DULL
BLADE DOES NOT CUTCLEANLY.
• WHEN SHARPENING BLADE, ENSURE THAT BATTERY
ISREMOVED.
REPLACE BENT OR DAMAGED
BLADE IMMEDIATELY
It is recommended that sharpening of blades be performed by
a D
eWALT factory service centre. However, blade edges may be
sharpened by using a fine tooth file
18
.
1. Run the trimmer until cutting blades
19
areoffset.
2. Be sure the lock-off lever is engaged, the blade has stopped,
and the battery has been removed before sharpeningblade.
3. Wear proper eye protection and gloves, and be careful not
to cutyourself.
4. Carefully file the cutting edges of the blade with a fine tooth
file. File toward the cutting edge
20
at the original cutting
angle (38 degrees from horizontal). File only the straight
cutting edges of the blades. Do not file where the cutting
edge curves into the centre of theblade.
5. Flip the trimmer over to sharpen the bottomblade.
6. Repeat steps to sharpen the opposite side of eachblade.

DeWalt DCMPH566 Specifications

General

Brand	DeWalt
Model	DCMPH566
Category	Trimmer
Language	English