English
10
XR Li‑ Ion tools are designed with an Electronic
Protection System that will protect the battery pack
against overloading, overheating or deep discharge.
The tool will automatically turn off if the Electronic
Protection System engages. If this occurs, place the
lithium‑ ion battery pack on the charger until it is fully
charged.
Wall Mounting
These chargers are designed to be wall mountable or
to sit upright on a table or work surface. If wall
mounting, locate the charger within reach of an
electrical outlet, and away from a corner or other
obstructions which may impede air flow. Use the back
of the charger as a template for the location of the
mounting screws on the wall. Mount the charger
securely using drywall screws (purchased separately)
at least 25.4 mm long with a screw head diameter of
7–9 mm, screwed into wood to an optimal depth
leaving approximately 5.5 mm of the screw exposed.
Align the slots on the back of the charger with the
exposed screws and fully engage them in the slots.
Charger Cleaning Instructions
WARNING: Shock hazard. Disconnect the charger
from the AC outlet before cleaning. Dirt and grease
may be removed from the exterior of the charger
using a cloth or soft non
‑
metallic brush. Do not use
water or any cleaning solutions. Never let any liquid
get inside the tool; never immerse any part of the tool
into a liquid.
Battery Packs
Important Safety Instructions for All
Battery Packs
When ordering replacement battery packs, be sure to
include catalogue number and voltage.
The battery pack is not fully charged out of the carton.
Before using the battery pack and charger, read the
safety instructions below. Then follow charging
procedures outlined.
READ ALL INSTRUCTIONS
• Do not charge or use battery in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Inserting or
removing the battery from the charger may ignite
the dust or fumes.
• Never force battery pack into charger. Do not
modify battery pack in any way to fit into a
non
‑
compatible charger as battery pack may
rupture causing serious personal injury.
• Charge the battery packs only in DeWALT chargers.
• DO NOT splash or immerse in water or other
liquids.
• Do not store or use the tool and battery pack in
locations where the temperature may fall below 4
˚C (39.2 ˚F) (such as outside sheds or metal
buildings in winter), or reach or exceed 40 ˚C (104
˚F) (such as outside sheds or metal buildings in
summer).
• Do not incinerate the battery pack even if it is
severely damaged or is completely worn out. The
battery pack can explode in a fire. Toxic fumes and
materials are created when lithium
‑
ion battery
packs are burned.
• If battery contents come into contact with the
skin, immediately wash area with mild soap and
water. If battery liquid gets into the eye, rinse
water over the open eye for 15 minutes or until
irritation ceases. If medical attention is needed, the
battery electrolyte is composed of a mixture of
liquid organic carbonates and lithium salts.
• Contents of opened battery cells may cause
respiratory irritation. Provide fresh air. If
symptoms persists, seek medical attention.
WARNING: Burn hazard. Battery liquid may be
flammable if exposed to spark or flame.
WARNING: Never attempt to open the battery pack
for any reason. If battery pack case is cracked or
damaged, do not insert into charger. Do not crush,
drop or damage battery pack. Do not use a battery
pack or charger that has received a sharp blow, been
dropped, run over or damaged in any way (i.e.,
pierced with a nail, hit with a hammer, stepped on).
Electric shock or electrocution
may result. Damaged battery packs should be returned
to
service centre for recycling.
WARNING: Fire hazard. Do not store or carry the
battery pack so that metal objects can contact
exposed battery terminals. For example, do not
place the battery pack in aprons, pockets, tool boxes,
product kit
boxes, drawers, etc., with loose nails, screws, keys,
etc.
To Next Page
Loading...
