Quick Start Guide
Tel: +1 (866) 446-3595 / (813) 888-9555
Technical Support Hours: 9:00AM – 8:00PM EST, Monday through Friday
digital-watchdog.com
Attention: This document is intended to serve as a quick reference for initial setup. It is
recommended that the user read the entire instruction manual for complete and proper installation
and usage.
4-Channel 8-Channel 16-Channel
DW-VA1G44 DW-VA1G48 DW-VA1G416
DW-VA1G442T DW-VA1G482T DW-VA1G4162T
DW-VA1G444T DW-VA1G484T DW-VA1G4164T
DW-VA1G446T DW-VA1G486T DW-VA1G4166T
DW-VA1G448T DW-VA1G488T DW-VA1G4168T
DW-VA1G441 0T DW-VA1G4810T DW-VA1G4161 0T
DW-VA1G4412T DW-VA1G4812T DW-VA1G41612T
DW-VA1G441 6T DW-VA1G4816T DW-VA1G41616T
DW-VA1G4820T DW-VA1G41620T
DW-VA1G4832T DW-VA1G41632T
Quick Start Guide
1. Mount and install all necessary cameras and external devices. Refer to their individual
manuals for additional information.
2. The DVR supports the following analog signals:
• HD-Analog
• HD-TVI
• Standard analog signal up to 960H
The DVR supports cameras up to 5MP (4K for 8/16CH models). Refer to the product’s data
sheet and full manual for recording specifications per product.
3. The DVR supports automatic signal detection. This means the DVR will detect the proper
signal automatically.
4. Place the DVR in its final position. See safety tips below.
5. Connect all necessary cables to the DVR.
6. Connect the DVR to an appropriate power supply.
The DVR will boot up automatically.
1. Make sure the cameras and the monitors are properly connected to the DVR.
2. The DVR should be placed in a dust and moisture free environment. It must never
be directly exposed to sunlight. A room temperature is highly recommended to reduce
the chance of overheating, (room temperature is considered as 68~78°F), which may
cause the DVR to become unstable.
3. During the boot up process, the DVR should not be interrupted by pressing any
buttons on the mouse. Do not unplug the power adapter or turn the DVR o during the
boot up process.
4. A UPS (uninterrupted power supply) is highly recommended to prevent damage to the
DVR during a power outage.
STEP 1 – CONNECTING THE DVR
SAFETY TIPS
NOTE: HD Monitor output and VGA output cannot be used at the same time for dual monitoring.
To prevent the DVR from overheating, do not operate it in an area that exceeds the maximum
recommended ambient temperature of 104°F (40°C). To prevent airflow restriction, allow
at least 3 inches (7.6 cm) of clearance around the ventilation openings.
Model Power consumption
DW-VA1G44 DC12V, 24W, 2A
DW-VA1G48 DC12V, 48W, 4A
DW-VA1G416 DC12V, 48W, 4A
WHAT’S IN THE BOX
Quick start guide
and download card
1 set
DC 12V adapter and
power cable
(*4-channel models do
not come with power
cable)
1 set
USB mouse 1 Rubber mounts – 4pcs 1 set
NOTE: Download all your support materials and tools in one place.
1. Go to: http://www.digital-watchdog.com/resources
2. Search your product by entering the part number in the ‘Search by Product’ search bar.
Results will populate automatically based on the part number you enter.
3. Click ‘Search’. All supported materials, including manuals and quick start guide (QSGs)
will appear in the results.
When the DVR boots up, it will be in protective mode
and the password setup screen will appear.
1. Setup a new password. The password must be a
minimum of eight (8) characters with at least four
(4) combinations of uppercase letters, lower-case
letters, numbers, and special characters.
2. When the DVR boots up for the first time, you will be
guided through the startup wizard.
STEP 2 – POWERING UP THE DVR
When logging into the DVR for the first time, you will be prompted to set up a new password. The new
password must include a minimum 8 characters with at least four combinations of uppercase and lowercase
letters, numbers, and special characters.
To Next Page
Need help?
General
