What causes blurred display on Distek Test Equipment and how to fix it?
To fix a blurred display on your Distek Test Equipment, adjust the display contrast by turning the multi-turn potentiometer on the stage board.
What to do if Distek Premiere 5100 Test Equipment has no stirring?
If there is no stirring, check the fuse (F5) for the motor on the motor/heater board to ensure it is not faulty.
What to do if my Distek Premiere 5100 has no heat?
If there is no heat, check for any defective triacs that stay off all the time when heaters are enabled.
What to do if Distek Premiere 5100 LED display not scrolling/locks up?
If the LED display is not scrolling or locks up, check the LED cable going from the motor/heater board (5103) to the LED board (5104) for any loose wires on the crimp connector.
What to do if Distek Test Equipment has no LED display?
If there is no LED display, check the ribbon cable that goes from the LED connector to the motor board for any loose wires or crimps.
How to fix Distek Test Equipment "CRITICAL ERROR"?
The "CRITICAL ERROR" indicates abnormal heating in the vessel. Ensure the calibration probe is plugged in, and then press ENTER.
How to level the Distek Test Equipment?
To level the unit, adjust the front leveling feet under the instrument base from front to back and side to side.
What causes noise in the drive assembly of Distek Test Equipment?
If there is noise in the drive assembly, check the drive motor’s conductive brushes for wear.
How to troubleshoot Distek Premiere 5100 no communication (handshaking) issue?
If there is no communication (handshaking), check the I/O cable for any faulty connections.
What to do if the shaft is not rotating but the Distek Test Equipment unit heats properly?
If the shaft is not rotating but the unit heats properly, check if the 0.5 amp fuse located on the 5103 PCB is blown.
Details system technical specifications like vessels, heating, RPM, display, and interfaces.
Outlines safety warnings, high voltage risks, and operational precautions for safe use.
Instructions for safely removing the instrument from its packaging and checking for damage.
Steps to ensure the instrument is level on the bench for accurate operation.
Procedures for installing and handling paddle blades and baskets for dissolution testing.
Critical operational parameter checks after installation to detect shipping or setup issues.
Explanation of the functions of each key on the instrument's control panel.
Overview of the instrument's LCD display and various operational screens.
Guidance on setting up and running pre-programmed dissolution test methods.
Procedures for controlling instrument parameters like RPM and temperature manually.
Essential procedures for calibrating temperature probes for accurate measurements.
Guidelines for routine cleaning, lubrication, and care of the instrument.
A guide to identifying and resolving common instrument problems and their solutions.
Steps to initialize the instrument, often after chip replacement or heating issues.
Contact information and procedures for obtaining technical support or arranging repairs.
List of available baskets with different mesh sizes and coatings.
Various kits and accessories offered, including press, visual aids, and manuals.
List of replacement parts for the instrument, including boards, fuses, and belts.
Tools for instrument validation and calibration, such as tachometers and wobble meters.
Example of a printout showing test method settings and parameters.
Example of a printout summarizing test results, including RPM and temperature data.
Example of an InstaPrint output showing real-time temperature and RPM data.
General| Model | Premiere 5100 |
|---|---|
| Type | Dissolution Test System |
| Manufacturer | Distek |
| Number of Stations | 6 or 8 |
| Compliance | USP, EP, JP |
| Stirring Speed | 25 to 250 RPM |
| Basket Speed Range | 25 to 250 RPM |
| Paddle Speed Range | 25 to 250 RPM |
| Temperature Accuracy | ±0.1°C |
| Temperature Resolution | 0.1°C |
| Vessel Volume | 1000 mL |
| Vessel Material | Borosilicate Glass |
| Power Requirements | 100-240 VAC, 50/60 Hz |
| Display | Touchscreen |
| Data Output | USB, Ethernet |
| Vessels | 6 or 8 |
To Next Page
