EasyManua.ls Logo

Dixon Bradford BC114 - User Manual

Dixon Bradford BC114
30 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Instruction & Operation Manual
Read and understand this manual prior to
installing, operating or servicing this equipment
BC-Series Centrifugal Pump
Updated March 2012

Table of Contents

Questions and Answers

  • J
    jamesfischerAug 14, 2025
    What to do if Dixon Bradford BC114 Water Pump motor overload?
    • G
      georgelopezAug 14, 2025
      If your Dixon Water Pump's motor is overloading or consuming excessive power, consider the following: * Restrict the discharge to lower the flow rate if the discharge is too high. * Inspect the pump for damage, misalignment, or interference if the impeller is binding, and replace any damaged or worn parts. * Inspect the pump and replace any damaged or worn parts if the seal is binding. * Increase the discharge head if the discharge is too low. * Ensure the electrical supply voltage or frequency is correct, making adjustments as needed, potentially replacing the motor. * Check the wiring for faulty electrical connections, repairing or replacing as necessary. * Inspect and replace overload heaters if they are too small.
  • R
    Ryan SwansonAug 25, 2025
    Why Dixon Bradford BC114 doesn't have enough pressure?
    • S
      Shannon KirbyAug 26, 2025
      A lack of pressure in your Dixon Water Pump could stem from several causes: * Air leaks in the seal or supply area (replace the seal if needed and repair any other air leaks). * Incorrect motor rotation (adjust the motor's electrical wiring). * Speed too slow because of low voltage, wrong frequency, wrong motor (adjust voltage and frequency; change motor if necessary). * Excessive air in the material (adjust the system to remove excess air).
  • J
    Janet RobertsAug 29, 2025
    How to solve rapid seal wear in Dixon Bradford BC114?
    • H
      hansenjesseAug 29, 2025
      Rapid seal wear in a Dixon Water Pump can be attributed to: * Improper installation of the mechanical seal (adjust the mechanical seal installation and replace any worn or damaged parts). * Dry running (ensure material is always in contact with the seal). * A loose or bent shaft (readjust shaft settings, tighten shaft screws if loose; if bent, replace the shaft and inspect the impeller hub for uneven wear, replacing the impeller if worn). * Water hammer (correct the system to prevent quick starts and stops).
  • K
    Kevin DelgadoSep 3, 2025
    What causes Dixon Water Pump leaks?
    • Y
      ysimmonsSep 3, 2025
      Leaks in a Dixon Water Pump can occur due to: * Issues with the inlet/outlet (inspect for missing union gaskets, loose connections, or damaged ports; replace worn gaskets and tighten loose connections; repair or replace damaged ports). * A loose casing clamp (tighten the clamp). * A damaged or worn casing gasket (replace the gaskets). * The seal not installed correctly (reassemble the seal properly and replace any worn or damaged parts). * A worn or damaged carbon seal (replace any worn or damaged parts). * A worn 'D' seal back plate (resurface or replace).
  • S
    sherijohnsonNov 8, 2025
    Why Dixon Water Pump has not enough or no discharge?
    • M
      Mrs. Emily MillerNov 8, 2025
      Several factors can cause insufficient or zero discharge in a Dixon Water Pump. It could be due to: * No fluid reaching the pump, requiring priming (installing a priming system is recommended). * A closed or blocked suction or discharge line (open the suction and remove any blockages). * Incorrect motor rotation (adjust the motor's electrical wiring). * A damaged impeller (replace the impeller). * Air leaks in the seal or supply area (replace the seal if needed and repair any other air leaks). * Excessive air in the material (adjust the system to remove excess air). * Discharge head or suction lift being too high (adjust the system to lower them). * Insufficient Net Positive Suction Head (NPSH) available (adjust the system to provide the correct NPSHa). * Speed too slow ...
  • E
    Eric MatthewsNov 18, 2025
    How to fix excessive vibration in Dixon Water Pump?
    • P
      prattdannyNov 18, 2025
      Excessive vibration or noise in your Dixon Water Pump can be addressed by checking these aspects: * Ensure the pump is level by inspecting its installation and correcting the level. * Verify that the piping support follows the recommendations in the installation portion of this manual for non-supported piping. * Inspect the pump and suction line for blockages, and adjust the suction line's length or size if there is not enough material reaching the pump. * Adjust the system to provide the correct NPSHa if there is insufficient NPSH available. * Replace worn parts if the impeller and/or shaft are worn. * Readjust shaft settings and tighten shaft screws if the shaft is loose, or replace the shaft and inspect the impeller hub for uneven wear if the shaft is bent; replace the impe...

Dixon Bradford BC114 Specifications

General IconGeneral
BrandDixon
ModelBradford BC114
CategoryWater Pump
LanguageEnglish