DKW RT 200 - Special Tools for Engine Service; Engine Service Tool Kit

No. 5 l Clutch spring pullar
. . . . . . . . . . . . . . . . . . . . . . . . . . ..e.........
No. 6
. Piston ring compraasor
....................................
No. 7 l Piston hnter cap
.........................................
. Elsctric Piston hratrr
....................................
with heatw alement
.......................................
No. 8 . Conmd tush rm&gtool
.................................
No. 9
. Punch for oil saals and ball borrings
.....................
No. 10
.
Holder for chain Sprocket
.................................
No. 11
. Clrping pitce ( to ba ussd with No. OltlX!M)
...........
No. 12 . Raducing pitca for ignition tiaing gauga
..................
No. 13
l Ignition timing gauge
.....................................
No.14 - Guide sleeve
..............................................
No. 15 - Annatura axtractiq holt
..................................
No. 16 .
Punch for Piston pin
......................................
No. 17
. Guide twi for Piston pin
..................................
No.18 . Extnctorrod fordmvels
..................................
No. 19
. Fork for countarreight support
...........................
No. in . Rooden forl< for Piston munting
...........................
No. 2l . Rulrr for alfgniq con-md
................................
6
No. OlOO'l61
No. olooa1-0
No. mom60-o
No.oloOl47
No. mool45
No. OlGGll9~
No.olaIa2xl
No. olm246-0
Na. Olm2444
No. olm~54
No. 0766
tb.ol002450
No. OlOOO27
No, rnoo249d
No. olm2494rl
~o,moc243~
~0.mm2540
No. mom62
No. 0100156
No. 22 l
Aligniq pin for ton-rPd
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
No. OlWl3
No. 23
. Gauge pin for ton-md
...........................................
No. OlOO214
':i:"i
.
(wi thwt
. Box spanner
.....................................................
No. olop6B-o
ill)
. Piston ring expander
............................................
No. 0162
See illustration
table 3
Crank shaft axtracter complete
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
kLrnal266~
Engine support for use with enginas RT 125,
RT. 200 and RT 250 ( sea ill. 1 )
_ No. 0100269-0
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Before fixiq cqins in thc support and aounting in vice, drain gear Oil.
The eng& support nursbsr~269~ consists of a U-plato to ba used forthe models RT 125,
RT 2UG and RT 250, and rhich tan be turned in all dindions, withthe aid of a joint-
piece, further of a bracket holding the joint piece in the vio and of various - indi-
vidually rr&ed - bolts.
Ths markings on the bolts show which of thea ars needed forths RT 125 and which ara
intended for the RT 200 / 2% models.
See illustration
table 4
Place engine support in horizontal position and lay ths engine - clutch side downwards
on top, then fix with the bolts supptied. The bolts arm also intended as supports for
the trank shaft extractor ( see ill.17 ).
7