WARRANTY
– Warranty Support and Service for DLX Technologies (DLX) products is provided by factory trained service techni-
cians and DLX Authorized Service Locations. The DLX warranty is valid for one (1) year to initial retail purchaser. The warranty is
limited to defects and workmanship in materials covering the paintball marker and regulator components. The electronic com-
ponents and solenoid are warranted for six (6) months. Disposable parts (Batteries, O-Rings, Seals, etc.) are not warrantied. This
warranty is effective only if the customer registers their marker online in our RMA system within 30 days of purchase. The warranty
is non-transferable. This warranty is limited to repair or replacement of defective parts with the customer responsible for transport-
ing the product to and from the Luxe
®
Paintball Authorized Service Location.
This warranty does not cover surface damages (scratches and nicks), misuse, or improper disassembly and reassembly. Attempts
made to drill holes or remove metal from external surfaces could degrade the performance and/or safety of the marker and may
only be preformed with written approval. The only authorized lubricant for the marker is GR33SE™ Lubricant. Use of any other lubri-
cant could result in reduced performance and invalidation of the DLX warranty.
Trigger alteration of any kind may result in serious injury, do NOT attempt to alter the trigger assembly in any way. Use of aftermar-
ket components within the bolt system, trigger or other operational components voids any warranty on the modied assembly and
its interacting systems. Removal of factory anodizing or other nish voids the warranty of any affected component as tolerances
will be effected by such action. DLX strongly discourages use of aftermarket internal components as they may jeopardize the
performance and/or safety of your paintball marker.
Luxe
®
and Freak
®
registered trademarks owned by DLX Technology Group.
QUICK START
GUIDE | V.01
LUXE SETUP
POWER CORE
WARNING!
– THIS IS NOT A TOY. MISUSE OF THE LUXE
®
MAY RESULT IN SERIOUS INJURY OR DEATH.
EYE PROTECTIONDESIGNED FOR PAINTBALL USE MUST BE WORN BY THE USER AND ANY PERSON WITHIN
RANGE OF THE LUXE
®
. DLX RECOMMENDS THAT THE LUXE
®
ONLY BE SOLD TO PERSONS 18 AND OLDER.
THOROUGHLY READ THE LUXE
®
QUICK START GUIDE BEFORE OPERATING.
INSTRUCTIONAL VIDEOS AND RESOURCES AT WWW.LUXEPAINTBALL.COM
WWW.LUXEPAINTBALL.COM
BATTERY
–
The lithium polymer battery in your Luxe
®
must be fully charged before use. To access the charging port on your
Luxe
®
, do so by removing the trigger frame back strap by pulling rearward on the nger grooves located at the bottom of the
backstrap {FIG. 01} Connect the USB Type C charging connector to the Luxe
®
circuit board. {FIG. 02} Once connected to the Luxe
®
,
power button will glow red when charging. When the Luxe
®
battery if fully charged the power button will turn green. The Luxe
®
is
compatible with standard USB and USB-C chargers, allowing it to be charged directly from a portable phone power pack, car USB
power source, laptop computer or other USB compliant power supply. The battery may also be removed and charged separately
with the optional Luxe
®
battery charger. Even if stored, the battery should be charged at least once every 6 months. NOTE: Battery
status is not shown when marker is charging. Approximate charge time is 45 min.
To install or remove the luxe battery just ip open or close the battery retaining clip {FIG. 03A} Note the correct orientation of the
battery before reinstalling {FIG. 03B} Close / lock the battery locking clip to secure the battery. {FIG. 03C}
WARNING!
–
The back strap cannot be re-installed until after the battery locking clip is in the down/locked position. {FIG. 03C}
01
BACK STRAP
WARRANTY
12
REINSTALL BACK STRAP
LUX761
02
CHARGING
03
BATTERY
A
B
USB-C
Fully Charged
Charging
A
B
C
Power
Button
REINSTALL BACKSTRAP
Tournament
Lock Entry
When re-installing the backstrap squeezeboth sides of the grip panel tight against the trigger frame to allow the backstrap to lock
into the grip panel sides. {FIG. 12}
IMPORTANT!
Make sure the backstrap is fully closed or the power button will not work.
11
POWER CORE
13
PROGRAMMING MENU
LUX709
LUX702.1 LUX708
LUX759.1 LUX660
SPR103
LUX626.1
LUX702
LUX759.2
OU7017
OM7020
OU7017
OU7014
OU7016
OU7015 OU7013
OB9016
OU7013
OU7012 OM7020
OU7005 OU9010
OU7015
OB7M26
Pinch
Both
Sides
Rotate
Down
To Next Page
Need help?
General
