Domo DO924DV User Manual

32
DO924DV
DE
2. Entfernen Sie die obere Abdeckung und den Temperaturregler vom Gefrierschrank.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
3. Entfernen Sie die Schrauben und anschließend das obere Scharnier, dass die Tür in ihrer
Position hält. Heben Sie die Tür hoch und legen Sie diese zur Vermeidung von Kratzern
auf inen weichen Untergrund.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
4. Entfernen Sie die unterste Schraube, den Scharnierbügel und den Stellfuß unten am
Gerät.
Reverse Door
Tool required: Philips screwdriver, Flat bladed screwdriver, Hexagonal spanner.
 Ensure the unit is unplugged and empty.
 To take the door off, it is necessary to tilt the unit backwards. You should rest the unit on something solid
so that it will not slip during the door reversing process.
 All parts removed must be saved to do the reinstallation of the door.
 Do not lay the unit flat as this may damage the coolant system.
 It' s better that 2 people handle the unit during assembly.
1. Remove two screws at rear side of top cover.
2. Remove top cover and thermostat knob, then place it aside.
3. Unscrew top hinge and then remove door and place it on a soft pad to
avoid scratch.
4. Unscrew bottom hinge. Then remove the adjustable feet from both
side.
7
unscrew
5. Lösen Sie den Scharnierbolzen aus dem Scharnierbügel. Kehren Sie das Scharnier um
und befestigen Sie den Scharnierbolzen wieder.
5. Unscrew and remove the bottom hinge pin, turn the bracket over and replace it.
6. Refit the bracket fitting the bottom hinge pin. Replace both adjustable
feet.
7. Place the door back on. Ensure the door is aligned horizontally and
vertically, so that the seals are closed on all sides before finally
tightening the top hinge.
8. Put the top cover and fix it with 2 screws on the back.
Unscrew
Screw
8
Reverse Door
9. Fix the thermostat knob.
screw

Domo DO924DV Specifications

General

Brand	Domo
Model	DO924DV
Category	Freezer
Language	English