What to do if my DOMOTECH Washer won't drain or drains too slowly and displays E1?
If your DOMOTECH Washer isn't draining properly and shows error code E1, the drain hose might be blocked. Check for any obstructions and clean out any foreign material. After clearing any blockage, push the start button again to resume operation.
Why does my DOMOTECH Washer stop during spinning and display E2?
If your DOMOTECH Washer stops during the spinning cycle and displays error code E2, it's likely because the top lid isn't closed properly. Make sure the top lid is fully closed to allow the cycle to continue.
What to do if my DOMOTECH Washer displays E4 and the water inlet isn't working?
If your DOMOTECH Washer displays E4 and the water inlet isn't working, check if the water faucet is open and that there's no water supply failure. Also, the water inlet valve might be blocked. Open the water faucet, and push the Start/Pause button again. If that doesn't work, clean the water inlet valve, and then push the Start/Pause button again.
How to fix abnormal sounds inside my DOMOTECH Washer?
If you hear abnormal sounds inside your DOMOTECH Washer, it could be due to several reasons: * The machine might be slanting. * There might be foreign materials inside. * The laundries might be unevenly distributed during spinning. To resolve this, adjust the machine to be level, remove any foreign materials, reorder the laundries evenly, and ensure the top lid is closed properly.
What to do if my DOMOTECH Washer displays E3 and the spinning doesn't work?
If your DOMOTECH Washer displays error code E3 and the spinning function isn't working, it's likely due to an imbalance. This can happen if the laundries are put in slantingly or if the machine itself is slanting. Reorder the laundries, close the top lid, and ensure the washing machine is set horizontally. Then, open and close the top lid once.
Why does my DOMOTECH Washer ring and display E0 after starting the reserve function?
If your DOMOTECH Washer rings and displays error code E0 after starting the reserve function, it means the top lid is open. Close the top lid to resolve the issue.
What to do if my DOMOTECH Washer displays E5 because the water temperature is too high?
If your DOMOTECH Washer displays E5, it indicates that the water temperature is too high (over 60°C). Allow the water to cool down, and then press the Start/Pause button.
What causes water faucet leaks in my DOMOTECH Washer and how to fix it?
If the water faucet leaks water in your DOMOTECH Washer, it could be due to a loose or twisted screw on the water inlet hose jointer. Properly fasten the screw of the jointer.
Why is there no water inlet in my DOMOTECH Washer?
If there is no water entering your DOMOTECH Washer, check the following: * Ensure the power plug is tightly plugged in. * Verify that the water faucet is open. * Confirm that the POWER ON/OFF and START/PAUSE buttons are pushed down.
What to do if there's no cascade current in my DOMOTECH Washer?
If there's poor or no cascade current in your DOMOTECH Washer, it might be due to foreign material blocking the spray outlet. Clear the foreign material to restore the cascade current.
Identifies all external and internal components of the washing machine.
Lists and describes included accessories with the washing machine.
Explains the meaning of warning and forbidding symbols used in the manual.
Guidelines for safe electrical connection, plug usage, and power cord care.
Precautions for machine placement, water temperature, and laundry types.
Warnings about operating the machine, user care, and preventing damage from misuse.
Advice on preparing laundry and basic maintenance safety precautions.
Instructions for attaching the bottom plate to the washing machine base.
Guidance on leveling the machine and ensuring proper installation slope.
Steps for installing the lint filter into the inner tub of the washing machine.
Instructions for changing drain hose direction and proper usage to ensure smooth drainage.
Steps and requirements for connecting the water inlet pipe to the faucet.
Instructions for connecting the water inlet hose to the washing machine inlet valve.
How to verify the stability and leak-free connection of the water inlet hose.
Procedures for safely disconnecting the water inlet hose from the faucet.
Key steps and checks before starting a wash cycle, including earthing and drain hose.
Guidelines for checking, sorting, and preparing laundries for washing.
Guidance on washing capacity, load balancing, and weight references for different laundry items.
Instructions for using the detergent box and correct dosages for various load sizes.
Methods and tips for dissolving washing powder and using whitener safely.
Explanation of the function of each button on the control panel.
How to select water inlet modes and water levels for washing.
How to select spin current and understand program modes.
Understanding the digitron display and using power, program, and select buttons.
How to set a delayed finishing time for the wash cycle.
A step-by-step guide on operating the washing machine using its buttons.
How to select specific wash procedures like WASH-SPIN, RINSE-SPIN, etc.
Detailed steps to select water inlet modes and water levels for washing.
A comprehensive table detailing water levels and wash times for each program.
How to select wash current, set reserve, start, and close the lid.
Instructions for removing, cleaning, and re-installing the detergent box and lint filter.
Guidance on cleaning the washing machine cabinet and general post-wash procedures.
A guide to diagnosing and solving common issues and error codes displayed by the machine.
Details the quantity and storage position of all items included in the washing machine package.
Provides key technical details of the washing machine, including voltage, capacity, and dimensions.
General| Model | XQB70-A |
|---|---|
| Spin Speed | 700 RPM |
| Body Material | Plastic |
| Display | LED |
| Frequency | 50Hz |
| Power Consumption | 320W |
| Type | Top Load |
| Capacity | 7.0 kg |
| Voltage | 220 V |
To Next Page