Donco 1555 User Manual

8"
Thank you for purchasing this quality product.
Be sure to check all packing materials carefully
for small parts which may have come loose
inside the carton during shipment. Separate,
identify and count all parts and hardware.
Compare with the parts list to be sure all parts
are present.
´´DO NOT TIGHTEN SCREWS
UNTIL COMPLETELY ASSEMBLED´´
SAFETY WARNINGS!
1- Follow the information on the warning label appearing on the upper bunk end structure and on the carton.
Do not remove warning label from bed.
2- Always use the recommended size mattress or mattress support, or both, to help prevent the likelihood
of entrapment or falls.
3- Surface of mattress must be at least 5 inchess below the upper edge of guardrails.
4- Do not allow children under 6 years of age to use the center and upper bunk.
5- Prohibit more than one person on Center and Upper bunk.
6- Periodically check and ensure that the guardrail, ladder and other components are in their proper position,
free from damage, and that all connectors are tight.
7- Do not allow horseplay on or under the bed and prohibit jumping on the bed.
8- Always use the ladder for entering and leaving the Center and Upper bunk.
9- Do not use substitute parts. Contact distributor or dealer for replacement parts.
10- Use of a night light may provide added safety precaution for a child using the Center and Upper bunk.
11- If the bunk bed will be placed next to a wall, the guardrail that runs the full length of the bed should
be placed against the wall to prevent entrapment between the bed and the wall.
12- Always use guardrails on both long sides of the Center and Upper bunk.
13- The use of water or sleep flotation mattresses is prohibited.
14- Keep these instructions for future reference.
15- Strangulation Hazard - Never attach or hang items to any part of the bunk bed that are not designed for
use with the bed: for example, but not limited to, hooks, belts, and jump ropes, etc.
IMPORTANT: PLEASE READ INSTRUCTIONS BEFORE STARTING THE ASSEMBLY
Inst
ct
io
s
n
ru
st
tio
c
s
n
ru
ASSEMBLY INSTRUCTIONS
1555 TRIPLE BUNK BED
SIZE OF MATTRESS AND FOUNDATION (SUPPORT)
total thickness must not exceed
inches. Do not use mattress without the proper bunkie board or safe
foundation.
Note:There must be at least 5" inches from top surface of mattress to top edge or guardrails.
TO OBTAIN PARTS, PLEASE CONTACT:
This bed is designed to use a twin mattress ( 37 ½”- 38 ½”x 74 - 75") and bunkie board (37 ½"x 74"). The
REPLACEMENT PARTS.
Replacement parts, including additional guardrails, may be obtained from place of purchase or original
distributor.
DONCO TRADING COMPANY- FORT WORTH, TEXAS

Donco 1555 Specifications

General

Brand	Donco
Model	1555
Category	Indoor Furnishing
Language	English

Summary

Product Overview and Safety Guidelines

Product Specifications and Mattress Guidelines

Information on product dimensions, mattress size compatibility, and foundation requirements.

Essential Safety Warnings and Precautions

Critical safety instructions for operating the bunk bed, covering entrapment and usage rules.

Assembly Preparation and Options

Ladder Placement Options and Tools Required

Illustrates choice between right/left ladders and lists necessary tools.

Component and Hardware Identification

Visual guide to all parts and hardware, detailing quantities and types.

Step-by-Step Assembly Instructions

Step 01: Initial Rail Assembly

Attaches initial side rails and guardrails using specified hardware.

Steps 02-03: Bottom Bed Frame Construction

Assembles the headboard and footboard for the bottom bunk.

Steps 04-05: Mid-Section and Guardrail Attachment

Connects bed sections and attaches guardrails using various fasteners.

Steps 06-07: Guardrail and Ladder Support Assembly

Installs longer guardrails and the first set of ladder supports.

Steps 08-09: Bottom Ladder Assembly

Assembles and attaches the ladder to the bunk bed structure.

Step 10: Installing Bottom Bed Slats

Attaches the wooden slats to the bottom bunk frame using screws.

Step 11: Installing Middle Bed Slats

Installs the slats for the middle bunk, ensuring correct spacing.

Steps 12-13: Top Bed Slats and Dowel Assembly

Attaches the top bunk's slats and uses dowels for support.

Steps 14-15: Top Bed Frame Construction

Assembles the headboard and footboard components for the top bunk.

Step 16: Connecting Major Frame Sections

Joins the assembled top and bottom sections of the bunk bed.

Step 17: Installing Bottom Bunk Slats

Secures the slats for the lowest bunk of the triple bed.

Steps 18-19: Top Bunk Slats and Top Ladder Assembly

Attaches remaining slats and assembles the top ladder.

Steps 20-21: Stacking Beds and Optional Right Ladder

Illustrates stacking levels and attaching the optional right side ladder.

Steps 22-23: Optional Left Side Ladder Assembly

Details the process of attaching the optional left side ladder.