DoorKing 1800-080 - Wiring and System Connections; Cellular Module Status LEDs; RS 232 and Phone Line Wiring; Two Entry System Wiring

3
1800-065 Issued 1-19
Version D
PH LINE
16VAC
16VAC
E GND
POWER
POWER
SOURCE
SYSTEM A
PROGRAM
MASTER
CODE
NORMAL
DATA
RESET
LINK
SYSTEM B
ON/OFF
Button
Ethernet
1800-010
PH LINE
DATA OUT
BUSY OUT
BUSY IN
GROUND
DATA IN
DATA OUT
RS 232
RS 232
BUSY OUT
BUSY IN
GROUND
DATA IN
PH LINE
PH LINE
NC
NO
RING
HF
1816
HS
ON
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
OFF
KEYPAD
321
3
321
MASTER
CODE
16AC16ACBAT1NO1NC1C2RY2CAZIMC
5VDCIMDSPKRCOMMICPSWCGNDPHONE
1
2
3
1 2 3 4 5 6 7 8 9 10 11121314
1
2
3
4
5
6
NC
NO
RING
HF
1816
HS
ON
SPK
VOL
FEED
BACK
RS 232
ELEVATOR
MIC
VOL
OFF
KEYPAD
321
321
321
MASTER
CODE
16AC16ACBAT1NO1NC1C2RY2CAZIMC
5VDCIMDSPKRCOMMICPSWCGNDPHONE
1
2
3
12345 67891011121314
1
2
3
4
5
6
SYSTEM A
1830
Voice/Data cellular system
should be as close as
possible to SYSTEM A.
SYSTEM B
Optional 1830
Main Terminal
Twisted Pair
MUST be used.
Twisted Pair Phone Line MUST be used.
500 ft RS 232 MAX
500 ft RS 232 MAX
DATA OUT-Red
DATA IN-Black
BUSY OUT-White
BUSY IN-Brown
GROUND-Green
RS 232 Connection
1
2
3
4
5
System A
Terminal
1830
Terminal
Supplied Power
Transformer
Earth
Ground
Voice/Data Cellular System
Data
Voice
Voice
Data
DKS Cellular Server
hosted by AT&T cellular network
with DKS Online Registration Completed
Wiring
Power
Icon
Signal
Strength
Bars
SIM
Status
Not Used
Program
Slide
Switch
Master
Code
Button
Ethernet
Data/Link
LEDs
RJ45
Cable
Cellular Module
TWO Entry Systems - The Voice/Data
cellular system can supply telephone
service and programming for TWO 1830s
designated as System A and System B.
The telephone line is SHARED with both
1830s. Each 1830 MUST be programmed
for Multiple Systems, see specific 1830
Installation/Owner’s instruction manual
for more information.
RS 232
RS 232
RS 232
“A”
RS 232
“A” LEDs
External
Antenna
Connection
RS 232
“B” LEDs
Cellular Power
Phone Jack
Board
Power
LED
RS 232
“B”
The EARTH GROUND must be connected to a proper
ground close by (ground rod, cold water pipe in the
ground, existing electrical ground, etc.).
Note: Older 1830 series circuit boards can be updated
to Rev W or higher for better DTMF tone distortion.
CELLULAR MODULE LEDs:
Signal Strength Bars:
Green - More bars, more signal strength.
Bars only display when call is being made.
SIM Status - Red blinking (error, usually NO SIM)
POWER Icon - ON (has power)
1816
Jumper
MUST be
Moved
1816
Jumper
MUST be
Moved
Do Not Connect Power
To A Receptacle
Controlled By
A ON/OFF Switch.
System B Phone Line Alternate Use - If system B is NOT being used for a
second phone entry system, a phone can be installed and used. It shares the
phone line with the System A phone entry system. The phone CANNOT be
used while a transaction is taking place on System A.
16.5VAC
40 VA
DATA OUT-Red
DATA IN-Black
BUSY OUT-White
BUSY IN-Brown
GROUND-Green
RS 232 Connection
1
2
3
4
5
System B
Terminal
1830
Terminal
LED on Enclosure Door
“AC power ON” indicator
Type of wiring to be used on ALL external devices:
A) Type CL2, CL2P, CL2R, or CL2X.
B) Other cable with equivalent or better electrical,
mechanical, and flammability ratings.
Wiring methods used shall be in accordance
with National Electrical Code, ANSI/NFPA 70.
Permissible wire sizes for the terminals (12-26 AWG).