Dremel A577 - User Manual

To Next Page

Prevent fingers from making

contact with rotating bit.

Do not tighten detailer’s grip

over shaft lock button.

Attachment for use with Dremel Rotary Tool

Models 100, 200, 300, 400, 4000, 800, 275, 285,

395, 398.

The attachment comes with its own nose piece

to tighten the handle to the tool.

Detailer’s Grip Attachment

Installation Instructions

Step 1: Remove the housing cap A from the

end of the tool and set housing cap aside. The

original housing cap must be reinstalled when

this attachment is not used (Fig. 1).

Step 2 & 3: Place handle B over housing collar

C with the handle in the desired position and se-

curely tighten the handle B with the nose piece

D that’s provided with handle (Fig. 2).

Make sure detailer’s grip is fully secured before

using tool.

Note: Attachment may not install flush onto

tool's housing.

Removing the Detailer’s

Grip Attachment

Step 1 & 2: Hold the handle B firmly and twist

the tool until the nose piece D is loose. Remove

nose piece D and handle B from housing collar

C and reinstall original housing cap A (Fig. 2).

Introduction

This attachment is designed to give you the ulti-

mate precision and control when working on

your projects. It is designed for you to hold and

control the tool like a pencil, between your thumb

and forefinger. When held in this position you

can hardly feel the weight of the tool. It is meant

to be an extension of your hand. To be comfort-

able with the Detailer’s Grip it is important to get

the “feel” of it. (See drawings for recommended

way to hold)

The Dremel Detailer’s Grip is intended to be

used on applications such as finishing sanding,

engraving, carving, etching, polishing, and

cleaning, to name a few.

1. Pencil Grip – For best control of the Detailer’s

Grip, hold the tool like a pencil between your

thumb and forefinger (Fig. 3).

2. Side Grip – Rotate the tool sideways, with the

handle pointing out while resting your hand

on the table (Fig. 4).

3. Stable Grip – For ultimate stability, rest the

handle of the tool on the table to help stabilize

and control the accessory (Fig. 5).

FIG. 1

FIG. 2

FIG. 3

FIG. 4

FIG. 5

Read and understand the manual for the use of the tool with this accessory.

SAVE THESE INSTRUCTIONS

WARNING

Detailer’s Grip Attachment Model A577

2610958466 03/09 Printed in Mexico

WARNING

CAUTION

P.O. Box 1468

Racine, Wisconsin 53401

1-800-437-3635

http://www.dremel.com

DM 2610958466 04-09:DM 2610958466 04-09 4/22/09 1:02 PM Page 1

Need help?

Do you have a question about the Dremel A577 and is the answer not in the manual?

Summary

Introduction to Dremel Detailers Grip Attachment

Pencil Grip Usage

For best control, hold the tool like a pencil between your thumb and forefinger.

Side Grip Usage

Rotate the tool sideways, with the handle pointing out while resting your hand on the table.

Stable Grip Usage

Rest the handle of the tool on the table to help stabilize and control the accessory.

Detailers Grip Attachment Installation Instructions

Step 1: Remove Housing Cap

Remove the housing cap A from the tool and set aside. Reinstall when not used.

Step 2 & 3: Attach Handle

Place handle B over housing collar C and securely tighten with nose piece D.

Removing the Detailers Grip Attachment

Steps 1 & 2: Detach Handle

Hold handle B firmly, twist tool until nose piece D is loose, remove handle and nose piece.