DT Research DT590BU User Manual

DT590BC/ DT590BU/ DT592BC/ DT592BU/ DT594BC/ DT594BU
ENGLISH
2
3
ENGLISH
Precauons
Always exercise care when operang and handling the • Medical Cart Computer.
Never disassemble any poron of the enclosure, as this will void any product warranty on the •
Medical Cart Computer.
Do not use any AC/DC adapter other than the one provided with the device or a replacement •
acquired from the manufacturer.
In the unlikely event that smoke, abnormal noise or strange odor is present, immediately power •
down the Medical Cart Computer and disconnect all power sources. Please report the problem
to your device provider immediately.
Basic Features
The Medical Cart Computer integrates a bright 19
”
, 22
”
, or 24
”
display with a high performance
system, USB ports, and integrated opons such as capacive touch, hot-swappable baeries, and
smart card reader for a comprehensive point-of-care soluon.
Powering ON and OFF
If your Medical Cart Computer comes with the baery packs, please open the baery slot caps and
then put in the baery packs one by one. If not, please use the AC-DC adapter with the Medical
Cart Computer for the power supply. To acvate the Medical Cart Computer, push and quickly
release the Power Buon and the display will come on in a few seconds. To put in Standby mode,
push and quickly release the Power Buon. To turn off for extended storage, power off the device
safely using any soware funcon that
“
shuts down computer
”
provided in the soware operang
system.
NOTE:
The baery packs shipped with your device may be low in power
—
please use the AC-DC adapter with the Medical
Cart Computer when seng up the device for the first me to fully charge the
baery packs. You may charge the
baery packs with them aached to the Medical Cart Computer, or with the oponal baery charger kit.
NOTE:
When the baery pack(s) is (are) charging, the blue-colored Baery LED should blink slowly. If plugging in the
AC-DC adapter does not trigger this blinking acvity and the LED stays dark, the baery pack(s) may have been
drained substanally. Try unplugging/
replugging the AC-DC adapter to the Medical Cart Computer a few mes to
acvate the charging process.
NOTE:
To conserve power, use (push and quick release) the Power Buon to put the device in
“
Standby
”
mode while not
in use. Pushing briefly on the same buon will wake up the system within seconds.
NOTE:
Avoid using the Power Buon (
“
hold 4+ seconds
”
feature) to turn off the device
—
this form of hardware shutdown
is intended to be a means of recovery from device lockups, and not as normal operaon.
NOTE:
If connecng an external monitor (via HDMI-out) to the Medical Cart Computer, you must power the computer
with the adapter.
Power/Baery LED Status
Blue indicates the baery is 25% to 100% charged•
Blinking blue indicates the baery is charging•
Orange indicates that the baery is between 11% to 25%•
Blinking Orange indicates that the baery is below 10%•
Wireless Networking
Wireless LAN
The Medical Cart Computer is oen delivered with an embedded (user-inaccessible) 802.11ac
WLAN adapter equipped with a hidden custom antenna.
Through the support of typical WLAN adapters, the Medical Cart Computer should be able to •
detect all 802.11 access points in the vicinity for you to select the access point of your choice for
connecon.
The SSID and WEP/WPA/WPA2 (if enabled) parameters on the Medical Cart Computer and the •
access points have to match. The SSID is case-sensive and it is recommended that you enable
WEP/WPA/WPA2 encrypon (or advanced alternaves) for secure access.
When WEP/WPA/WPA2 is enabled, you may need to consult your network administrator or your •
networking equipment literature to properly configure associated sengs such as Authencaon
mode, etc.
Refer to the access point operang manuals for seng up the 802.11 access points.•
Bluetooth
The Medical Cart Computer features a built-in Bluetooth adapter that operates on the Microso
Windows Bluetooth protocol. The Bluetooth configuraon applicaon is invoked from the System
Tray or from the Control Panel. Follow the instrucons and opons provided within the applicaon
to configure and invoke Bluetooth connecvity with the corresponding peripherals.
NOTE:
Bluetooth devices or accessories that are not compable with the Microso Windows Bluetooth protocol may not
work with the Medical Cart Computer.
Baery Indicator
Baery Indicator

DT Research DT590BU Specifications

General

Brand	DT Research
Model	DT590BU
Category	Medical Equipment
Language	English