A
C
B
N
N
B
B
K
L
I
Tools Needed:
// Allen Wrench – 5/32” // Drill // Pliers
// Socket – 7/16” // 7/16” Drill Bit
// Socket – 3/8” // Marker or Pencil
// Phillips Screwdriver – #3 // Jack-Nut Friction Wrench (supplied)
Installation Instructions:
The Tote may be placed on either side of the truck bed. It is recommended that the lid open towards the
middle of the truck bed for ease of access inside the Tote.
On the end of the Tote that will face the rear of the vehicle, attach one Stopper (I) to the Tote
in each corner with one Bolt – 1/4” x 3/4” (J) and attach the Lock Swivel (M) in desired corner, as
pictured.
Attach the Base Plate (A) to each Channel (B) with two Screws – Flat Head 1/4” x 1/2” (C)
using an Allen Wrench – 5/32”. Insert the four Adjustable Feet (N) into the pre-drilled holes in
the bottom of each Channel (B).
Attach the Lock Latch (K) in the pre-drilled holes on the side of the Channel (B) with two Screws –
#8 x 5/16” (L) using the Phillips Screwdriver. (Note: Make sure the location of the Lock Latch (K)
corresponds with the Lock Swivel (M) you attached to the Tote in Step 1.)
Place the Tote and Base Plate (A) with Channels (B) into the vehicle in desired location.
Slide the Tote into the Base Plate (A) with Channels (B) until the Stoppers (I) contact the Channels.
Note: Make sure the Lock Latch (K) and the Lock Swivel (M) are aligned and function properly.
Make sure the Tote is positioned properly and the tailgate of the vehicle closes without contacting
the Tote. It is recommended to have at least 1“ clearance in between the Tote and the tailgate.
Make marks at the location of the Base Plate (A), as pictured, using a marker or pencil. Hold the
bracket fi rmly in place and remove the Tote.
Continued on Page 2...
Tote Slide Bracket
Installation Instruction
DU-HA, Inc. // website: www.du-ha.com // phone: 1.866.306.DUHA (3842) // fax: 1.218.998.4013 // 306 Saint Andrews Street South, Fergus Falls, MN 56537
1
2
3
4
5
A
B
B
D
D
G
F
Option 2 — Jack-Nuts
Option I — Self Tapping Screws
H
I
J
J
I
K
L
N
C
M
N
N
N
Fits DU-HA Tote Part Number: 70103
Part Description Qty
A Base Plate 1
B Channel 2
C Screws – Flat Head 1/4” x 1/2” 4
D Jack-Nut – 1/4” 2
E Nut – 1/4” (used in SUV install only) 2
F Self Tapping Screws – 1/4” x 2-1/2” 2
G Bolt – Hex Head 1/4” x 2-1/2” 2
H Washers – Flat 1/4”
(2 used in SUV install) 4
I Stoppers 2
J Bolt – 1/4” x 3/4” 2
K Lock Latch 1
L Screws – #8 x 5/16” 2
M Lock Swivel 1
N Adjustable Feet 4
70104
1
2
3
M
I
J
I
J
C
4
E
Not pictured.
Rear of Vehicle
Mark Locations
A
5
PICKUP TRUCK
To Next Page
Need help?
General