Dunelm Bay Curtain Pole

Need help?

Do you have a question about the Dunelm Bay Curtain Pole and is the answer not in the manual?

Summary

Tools and Parts

Parts Included

Components provided with the bay curtain pole kit.

Prepare Wall for Installation

Marking Bracket Positions

Using a tape measure and level, mark bracket positions on the wall as shown.

Fit Wall Brackets

Drill holes, fit wall plugs, and screw wall plates to the wall.

Bend Poles Correctly

Correct Pole Bending Technique

Bend poles with slots facing inward, using two people for support.

Incorrect Pole Bending

Avoid bending poles with slots facing outward or without proper support.

Adjust Poles for Fit

Pole Bending Guidance

Use wall or skirting to guide the degree of bend for the poles.

Pole Cutting Instructions

Cut poles to fit window, ensuring equal lengths for joins and finishing 10cm from the last bracket.

Assemble Curtain Pole

Assembly Step 1: Center Bracket

Fit the center bracket to the wall and tighten the bottom rear screw.

Assembly Step 2: Feed Brackets

Feed curtain and two brackets onto pole section, ensuring they don't slide from the middle joint.

Assembly Step 3: Fit Poles to Bracket

Slide middle pole end into center bracket, fit end brackets, tighten only rear screws.

Assembly Step 4: Join Poles

Fit joiner into middle section of pole and repeat steps for the other pole.

Assembly Step 5: Level and Secure

Clip level, tighten all screws ensuring pole is level, then slide and tighten finials.

This document provides installation instructions for a Dunelm Bay Curtain Pole.

Function Description:

The Dunelm Bay Curtain Pole is designed to support curtains around a bay window. It consists of multiple pole sections, brackets, joiners, and finials, allowing it to be custom-fitted to the specific dimensions and angles of a bay window. The pole sections are designed to be bent to match the angles of the bay, and their length can be adjusted by cutting. The system includes wall-mounted brackets for secure installation and finials for a decorative finish.

Important Technical Specifications:

Components: The product includes:
- 5 wall brackets (x5)
- 2 pole sections (x2)
- 1 joiner (x1)
- 15 screws (x15)
- 15 wall plugs (x15)
- 1 level (x1)
- 1 finial (x1)
- 2 additional unspecified components (x2)
Tools Required: The installation requires a tape measure, level, drill, and screwdriver.
Installation Requirements: Two people are required for installation, particularly for bending the poles.
Wall Compatibility: Depending on the type of wall, additional fittings may be required. Users are advised to consult a local hardware store if unsure.
Pole Bending: The poles are designed to be bent, with specific slots facing the inside of the bend.
Pole Length Adjustment: Poles can be cut to fit the window, ensuring equal lengths to hide the join between the middle bracket. The outward end of the pole should finish approximately 10cm away from the last bracket.

Usage Features:

Customizable Fit: The modular design with bendable and cuttable pole sections allows for a precise fit to various bay window configurations.
Aesthetic Integration: The design aims to blend with the window structure, with instructions to cut poles to hide joins and ensure a clean finish.
Secure Mounting: Wall brackets are screwed into the wall with plugs, providing a stable support for curtains.
Level Installation: A small level is included to ensure the pole is installed horizontally.
Decorative Finials: Finials are added to the ends of the pole for a complete and decorative appearance.

Maintenance Features:

The manual does not explicitly detail maintenance features. However, as a curtain pole, general maintenance would likely involve occasional cleaning of the pole and finials to remove dust and dirt.
Regular checks of the bracket screws for tightness might be advisable to ensure continued stability, especially if heavy curtains are used.
Should any part become damaged, individual components might be replaceable, though this is not specified in the provided pages.

Installation Process Overview:

Preparation: Mark bracket positions on the wall using a tape measure, level, and a wall bracket as a guide.
Fit Wall Brackets: Drill holes, insert wall plugs, and screw wall plates to the wall.
Bend Poles: With two people, bend the pole sections, ensuring the slots face the inside of the bend. This step is crucial and should be done carefully to avoid damage.
Cut Down Poles: Measure and cut pole sections to fit the window, ensuring equal lengths for the middle section and leaving approximately 10cm from the last bracket to the pole end.
Assembly - Step 1: Fit the center bracket to the wall and tighten the bottom rear screw.
Assembly - Step 2: Feed curtains and two brackets onto one pole section. Do not tighten screws yet.
Assembly - Step 3: Slide the middle end of the pole into the center bracket. Fit end brackets. Only tighten the rear screw of the center bracket.
Assembly - Step 4: Fit the joiner into the middle section of the pole and repeat steps 2 and 3 for the other pole section.
Assembly - Step 5: Clip the included level to the pole and tighten all screws, ensuring the pole remains level.
Final Check: Check the function and position of the pole. Once satisfied, slide finials onto the ends of the pole and tighten their screws.

Important Notes for Installation:

It is recommended that installation be performed by individuals competent in DIY. If in doubt, consult a professional.
Read all instructions thoroughly before beginning installation.
Depending on wall type, additional fittings may be necessary. Consult a local hardware store for advice if unsure.
Crucially, refer to page 3 before attempting to bend the pole. Incorrect bending can damage the product.
During assembly, pay close attention to which screws are tightened and when, as specified in the steps.