Dyna-Glo DGW1235BDP-D-1

Questions and Answers

J
Joshua PerezAug 16, 2025
What to do if Dyna-Glo Smoker has flare-up?
- M
  Michael StevensAug 16, 2025
  If your Dyna-Glo Smoker experiences a flare-up, it could be due to several reasons. First, you might be cooking at excessive temperatures, so try reducing the flame level. Grease and residue build-up can also cause flare-ups, so ensure you clean the components regularly. If you're cooking meat with excessive fat, trim the fat before cooking. Finally, marinades with excessive oil can lead to flare-ups, so consider using a non-oil based marinade.
M
Melissa BenjaminAug 19, 2025
Why is the flame yellow and sooty on my Dyna-Glo Smoker?
- C
  Cindy SanchezAug 19, 2025
  A yellow and sooty flame in your Dyna-Glo Smoker can be caused by several factors. It may be due to excessive cooking temperature, so try reducing the flame level. Another cause could be an obstruction of gas flow, in which case you should check and clean the venturi tube and burner. Lastly, ensure that the ventilation is properly adjusted and the damper is open.
C
Christopher AlexanderAug 22, 2025
How to fix Dyna-Glo Smoker burner that won't light with igniter?
- A
  Amy WilliamsAug 22, 2025
  If the burner on your Dyna-Glo Smoker won't light using the igniter, there are several potential causes. First, the igniter electrode may be covered with grease or residue, so try cleaning it. Next, check for loose or disconnected wires on the igniter electrode and reconnect them if necessary. If no spark is being generated, replace the AAA battery inside the igniter. Also, ensure that the LP cylinder is not empty and the cylinder valve is open to allow gas flow. Finally, a vapor lock may have occurred. Turn off the control knob and LP cylinder valve, disconnect the coupling nut from the LP cylinder, then reconnect and try again.
T
Tyler TrevinoAug 25, 2025
What to do if Dyna-Glo Smoker flame goes out?
- S
  sandra21Aug 26, 2025
  If the flame on your Dyna-Glo Smoker keeps going out, there are a couple of things to check. First, make sure the gas supply hose is properly connected. If it's disconnected, reconnect it. Also, high or gusting winds can extinguish the flame, so move the smoker out of the windy area.
C
carolyn31Aug 28, 2025
What to do if Dyna-Glo Smoker burner won't light with a match?
- J
  John GarciaAug 28, 2025
  If the burner on your Dyna-Glo Smoker won't light with a match, it's likely due to no gas flow or an obstructed gas flow. Check the fuel level and clean the venturi tube and burner.
J
Jessica HarveyAug 31, 2025
What to do if my Dyna-Glo Smoke Alarm is flaring up?
- R
  Robert KellerAug 31, 2025
  Flare-ups on your Dyna-Glo Smoke Alarm can occur due to several reasons. You might be cooking at excessive temperatures, so try reducing the flame level. Grease and residue build-up can also cause flare-ups, so be sure to clean the components regularly. If you're cooking meat, trim excess fat before cooking. Finally, avoid oil-based marinades, as excessive oil can contribute to flare-ups; use a non-oil based marinade instead.
R
Rick SantosSep 3, 2025
Why won't my Dyna-Glo DGW1235BDP-D-1 Smoke Alarm burner light with the igniter?
- J
  Jessica BeardSep 3, 2025
  If the burner on your Dyna-Glo Smoke Alarm won't light using the igniter, several issues could be the cause. The igniter electrode might be covered with grease or residue; if so, clean the igniter electrode. Also, the igniter electrode may have a loose or disconnected wire, so check the connection and reconnect any loose wires. If no spark is being generated, replace the AAA battery inside the igniter. Ensure that the LP cylinder isn't empty and that the cylinder valve is open. Finally, a vapor lock may have occurred at the coupling nut to the LP cylinder; in this case, turn off the knob and LP cylinder valve, disconnect the coupling nut, reconnect it, and try again.
J
Jessica JohnsonSep 6, 2025
How to fix a yellow sooty flame on my Dyna-Glo DGW1235BDP-D-1?
- J
  Jamie SmithSep 6, 2025
  A yellow, sooty flame on your Dyna-Glo Smoke Alarm can be caused by a few things. It could be due to excessive cooking temperature, so reduce the flame level. Another cause might be an obstruction of gas flow; check and clean the venturi tube and burner. Also, check if the ventilation or damper is closed; if so, adjust them accordingly.
D
dmitchellSep 9, 2025
What to do if the flame keeps going out on my Dyna-Glo DGW1235BDP-D-1 Smoke Alarm?
- R
  Rachel DavisSep 9, 2025
  If the flame on your Dyna-Glo Smoke Alarm keeps going out, it could be due to a disconnected gas supply hose; make sure to reconnect it. High or gusting winds can also cause the flame to extinguish, so move the grill out of the windy area.
M
Mr. Nathan Delgado DVMSep 12, 2025
Why Dyna-Glo DGW1235BDP-D-1 Smoke Alarm burner will not light with a match?
- K
  Kristen LeeSep 12, 2025
  If the burner on your Dyna-Glo Smoke Alarm won't light with a match, it's likely due to no gas flow or an obstructed gas flow. Check the fuel level and clean the venturi tube and burner.