DynaLock 3000 Series User Manual

PLEASE READ BEFORE ATTEMPTING INSTALLATIONS
3000/ 3000LC/ 2000 SERIES CIRCUIT BOARD DESCRIPTION
Refer to Page 2 & 3 for wiring and voltage instructions
Power Input
and
Control
Fig "A, B & E"
Door
Status
Fig "D"
Dynastat
Fig "C"
L2 OPTION - FUNCTION
Requires Dynastat option to work.
Red = secure / Green = unsecure
Reversing plug direction changes
light indication.
ATS OPTION - WIRING
Indicator device, by others,
illuminates / sounds
when access cover is removed.
Contact Rating: SPDT @ 0.5A
DYNASTAT
CONNECTOR
TIME DELAY ADJ.
CW to increase.
Range 1-80 seconds
see fi g. "E"
 3000/2000 series mag lock accepts 12/24 VAC/DC
 Circuit board shown fully loaded, with every option
ATS
SWITCH
LED
3 Pin Plug
LOCK HOUSING
Wht
Wht
2 Pin Plug
not polarized
COIL CONNECTOR PLUG
The Coil Connector is not polarized
and may go on in either direction.
Blk
Blk
Wht
Wht
4 Pin Plug
COIL PLUG RECEPTACLE
VOLTAGE SELECTION
JUMPERS -
See page 2
SECURE
TAMPER
POWER INPUT
FOR ATS
OPTION
GRN
WHT
RED
COM.
NO
NC
1
DynaLock Corp. z 705 Emmett Street z P.O. Box 2728 z Bristol, CT 06011-2728 z 1-877-DYNALOCK z www.dynalock.com
Electromagnetic Locking Systems

DynaLock 3000 Series Specifications

General

Brand	DynaLock
Model	3000 Series
Category	Locks
Language	English

Summary

3000/3000LC/2000 Series Circuit Board Description

Coil Connector Plug

Details on the non-polarized coil connector and its connection to the circuit board.

Power Input for ATS Option

Wiring configuration for the ATS (Accessory Tamper Sensor) option power input.

ATS Option Wiring

Description of the ATS option's wiring for indicator devices and its contact rating.

Time Delay Adjustment

Information on adjusting the time delay feature, including its range and control.

Dynastat Connector

Details regarding the Dynastat connector and its function with the L2 option.

L2 Option Function

Explanation of the L2 option, requiring Dynastat, and its light indication reversal.

How to Set Voltage

Voltage Selection Jumpers

Instructions for setting the lock's operating voltage using jumper caps.

Wiring Instructions

Figure A: 12/24 VDC Input

Diagram for connecting 12/24 VDC input power and station controls.

Figure B: 12/24 VAC Input

Diagram for connecting 12/24 VAC input power and station controls.

Figure C: Dynastat Option

Wiring diagram for the Dynastat option, including door secure/unsecure indicators.

Figure D: DSM Option

Wiring diagram for the DSM (Door Status Monitor) option.

Time Delay Option Wiring

Figure E: Time Delay Operation

Wiring and operational steps for the Time Delay (TD) option.

Electrical Specifications

Coil Resistance Check

Procedure and expected resistance values for checking the magnet coil.

Troubleshooting Tips

Door Will Not Lock or No Magnetic Holding Force

Troubleshooting steps for issues with locking or holding force.

Low Holding Force

Diagnosing and resolving problems related to reduced holding force.

Magnet Overheats / Draws Excess Current

Troubleshooting tips for overheating magnets or excessive current draw.

Dynastat Sensor Not Indicating Door Secure

Steps to resolve issues with the Dynastat sensor not indicating a secure door.

DSM Not Indicating Door Closed/Open Status

Troubleshooting for the DSM feature not reporting door status correctly.

LP - Low Power Option Supplemental Instructions

General Information for Low Power Option

Overview of the Low Power option, operating voltage, and current draw.

Basic Input Power Wiring for Low Power Option

Wiring diagrams for 12 VDC and 12 VAC input for the Low Power option.

Series 2000/3000 x LCB Electromagnetic Lock Wiring Instructions

12 Volt DC Operation Wiring

Wiring instructions for 12 Volt DC operation, including MOV placement.

24 Volt DC Operation Wiring

Wiring instructions for 24 Volt DC operation, including MOV and jumper.