e-LinkCare ACCUGENCE PM900 - User Manual

66 pages

Save Page as PDF

To Next Page

Multi-Monitoring System

Thank you for choosing ACCUGENCE® Multi-Monitoring System (Model: PM900).

You now have a very simple and accurate way to test your Blood Glucose, β-Ketone

and Uric Acid from fresh whole blood samples in just a few simple steps anytime,

anywhere.

Attention: ACCUGENCE® Blood Glucose Test Strips with ACCUGENCE® Multi-

Monitoring System are intended for in-vitro diagnostic self-testing by people with

diabetes and healthcare professionals in clinical settings. ACCUGENCE® Blood

Ketone Test Strips and ACCUGENCE® Uric Acid Test Strips with ACCUGENCE® Multi-

Monitoring System are intended for in-vitro diagnostic for self-testing and

professional use.

To ensure accurate results from your ACCUGENCE® Multi-Monitoring System,

please follow these guidelines carefully:

• Read instructions before use.

• ACCUGENCE® Multi-Monitoring system is intended for in- vitro diagnostic use

only. It is intended to be used with ACCUGENCE® Blood Glucose Test Strips,

ACCUGENCE® Blood β-Ketone Test Strips, and ACCUGENCE® Uric Acid Test

Strips to quantitatively measure glucose, β-hydroxybutyrate (β-ketone), and

uric acid from whole blood sample.

Note: There are two types of ACCUGENCE® Blood Glucose Test Strips available,

ACCUGENCE® Blood Glucose Test Strips using Glucose Oxidase (GLU GOD) and

ACCUGENCE® Blood Glucose Test Strips using Glucose Dehydrogenase FAD-

dependent (GLU GDH).

• ACCUGENCE® Multi-Monitoring Meter with ACCUGENCE® Blood Glucose Test

Strips are intended for use by people with diabetes mellitus at home and by

healthcare professionals in clinical settings as an aid to monitor the

effectiveness of diabetes control. It is not intended for use in the diagnosis of

or screening for diabetes mellitus.

Note: When ACCUGENCE® Blood Glucose Test Strips (Glucose Oxidase) are used,

only fresh capillary whole blood is allowable to be used for testing. When

ACCUGENCE® Blood Glucose Test Strips (Glucose Dehydrogenase FAD-

dependent) are used, fresh capillary whole blood or venous whole blood is

allowable to be used for testing, but venous whole blood testing is limited for

professional use only.

• ACCUGENCE® Multi-Monitoring Meter with ACCUGENCE® Blood Ketone Test

Strips are intended for use for the quantitative measurement of β-

hydroxybutyrate (β-ketone) in fresh capillary whole blood or venous whole

Questions and Answers

E
Elizabeth ThompsonNov 4, 2025
How to fix e-LinkCare Medical Equipment meter that fails to turn on?
- N
  Nancy GonzalezNov 4, 2025
  If your e-LinkCare Medical Equipment meter fails to turn on, several factors could be the cause. The battery might be damaged or not charged, so try replacing it. If the meter has been in cold conditions, allow it to reach room temperature (about 30 minutes) before testing again. There may be a Power On self-check error; in this case, remove the battery for 30 seconds, reinsert it, and try again. If the problem continues or there is an Internal calibration check error, contact your local distributor. A contaminated, used, or moisture-exposed test strip can also cause this, so repeat the test with a new strip. Ensure you apply the sample after the blood drop/test strip symbol appears and apply enough sample to fill the test strip check window. Also, apply the sample within 3 seconds to avoi...
A
Adrienne McculloughNov 19, 2025
What to do if e-LinkCare ACCUGENCE PM900 Medical Equipment shows anomalous temperature change?
- S
  Samuel BradyNov 19, 2025
  If the operation temperature of your e-LinkCare Medical Equipment has changed anomalously, double-check that the operating conditions are steady and repeat the test. If the temperature has exceeded the system's operating temperature, move to a cooler environment and repeat the test. If the temperature is below the operating temperature, move to a warmer environment and repeat the test. If you suspect hardware damage, please contact your local distributor for a meter replacement. A failure or damage of the calibration chip could also be the reason, so replace the calibration chip and perform the test again. Ensure the calibration chip is matched; if not, replace it. If you see a communications failure or the test strip starts flashing "---" while connected to a cable, consult the ACCUGENCE®...

Summary

Getting Started

Components Descriptions

Overview of system components like meter, strips, lancets, control solutions, and carrying case.

Meter Display

Explanation of various icons, indicators, and display segments on the meter's LCD screen.

Installing Batteries

Step-by-step guide for opening the battery cover and inserting the required CR2032 coin cell batteries.

Meter Setup Before Testing

Instructions for setting the clock, date, and other meter preferences before the first use.

Testing Your Blood

Getting a Drop of Blood

Instructions on preparing the fingertip and using the lancing device to obtain a blood sample.

Testing Your Blood Glucose

Detailed procedure for performing blood glucose tests, including inserting strips and applying blood.

Testing Your Blood ß-Ketone

Instructions for performing blood beta-ketone tests, including coding the meter and applying the sample.

Testing Your Uric Acid

Procedure for measuring uric acid levels, including inserting the correct strip and applying the sample.

Recall the Meter Memory

Viewing Stored Records

How to access and review previously recorded test results, including date, time, and measurement.

Clearing the Memory

Instructions on how to delete all recorded test data from the meter's memory.

Transferring Records

Guide on connecting the meter to a PC to transfer and manage test data using software.

Troubleshooting Guide

Error Messages and Solutions

Explains common error codes displayed by the meter and provides corresponding solutions.

Specifications

Technical Specifications

Detailed technical data including measurement ranges, sample sizes, test times, and operating conditions.

Index of Symbols

Symbol Definitions

Explains the meaning of various symbols used in the manual and on the device for clarity.

Warranty Card

Warranty Information and Registration

Details on product warranty coverage, conditions, and how to register the purchase.

Contact Address

Information for contacting customer support or the local dealer for assistance.

e-LinkCare ACCUGENCE PM900 Specifications

General

Category	Medical Equipment
Model	ACCUGENCE PM900
Type	Patient Monitor
Parameters	ECG, SpO2, NIBP, TEMP, Respiration
Power Supply	AC 100-240V, 50/60Hz
Battery	Rechargeable lithium-ion battery
Alarm	Audible and visual alarms
Connectivity	USB
Display	12.1-inch TFT LCD
ECG	3/5-lead ECG, HR, ST segment analysis, arrhythmia analysis