1 6 E S C C h e c k a n d F l a s h f i r m w a re
.
1 3 R a d i o c h a n n e l s /S w i t c h a n d B e t a fl i g h t m od e s e t t i n g
.
1. Do w nl o ad N ew r el ease Blh el i su it e f ro m :
2. Co n n ect t h e N O VICE- III f l i g h t co n t ro l l er t o co m p u t er
h t t p s:/ / ww w.m ed i af ire.co m / f o ld er/ d x6k f aasyo 24l/ BLH el iSui t e
3. Op en t h e D evice M anag er o f yo ur co m p ut er, f i nd t h e Por t s, p lease m ake su re
t h e Co m p o r t Ser i al N u m b er i s un d er 2 55, ot her w ise it w ill can' t co n nect t o t h e
BLH ELISUITE. Yo u can ch ang e t he p o r t ser ial n um b er li ke t h e b el lo win g st ep :
4. Op en t h e BLH ELISUITE, Sel ect SILABS BLH eli Bo o t l oad er (Cl ean f li g h t ) f r o m
t h e t h ird t ab o n t h e t o p si d e. Th en Sel ect t h e r i g h t Seri al co m p o r t an d Cli ck
co n nect . You can also Flash t h e n ew r elease BLH el i_s f irm ware vi a t h e
BLH EILISUITE, t h e f ir m w ar e Targ et i s “F- H - 40”
Cli ck ch eck t o see t h e
d et ai l s of t h e 4i n 1 ESC
Firm w ar e t ar g et
Flash f i r m w ar e
1. Install latest STM 32 Virt ual COM Po rt Driver
2. Install STM BOOTLOAD Driver (STM Device in DFU MODE)
3. Open Bet aflight config urat or and choose firm ware targ et “M ATEKF411RX”,
then select the firm ware version.
4. There are 2 ways to get in DFU M od e: 1). Press and ho ld t he boot button then ,
plug USB to comp uter 2).loading bet aflight firm ware and hit “flash”, then it will
get ting into DFU M od e autom at ically.
5. Open Zadig to o ls to rep lace the drivers fro m STM 32 Bootloader to WIN USB Driver.
6. Recon nect the flight cont ro ller to the co m put er after rep lace driver done , and
op en Bet af light Config urat or, loading firmware and flash.
ht tp:/ / www.st.com / web / en/ catalo g / tools/ PF257938
1 7 F l i g h t c o n t ro l l e r f i r m w a r e u p d a t e
.
- -4
SWA
SW B
SW C
SW B
1 4 M e n u I nt r o d u c e
.
1:An t enn a
2:SB Po si t i o n
3:SD Posi t io n
4:UP Bu t t o ns
5:Do w n Bu t t o n s
6:LED
7:M D L/ LEFT But t o n s
8:Gi m b al
9:T1- T4 Tri m But t o n
10 :Po w er But t o n
11 :SA Po si t io n
12 :SC Posit i o n
13:
14:RNT But t ons
15:1.3" LCD screen
16:SYS/RIGHT Buttons
17:Gim ba
18:T1- T4 Trim But ton
19:Speaker
20:Sing le 18650 battery power supp ly
21:Ext ernal module
ENT Buttons
Current M odel
Bat tery Volt age
Left Stick
Trims
Rig ht St ick
Trims
Stick Position
Numeric values
M odel Selection
M ixes setup
1.Press t h e M en u b u t t o n
an d sel ect t h e M o d el
m em o r y sl o t yo u w i sh t o
u se.
3.SA sw it ch w as set t o
ar m o r d isarm t h e q u ad .
SB sw i t ch w as set t o
ch an g e f lyin g m o d e. SC
sw it ch w as set t o act i ve
Beep er.
2.M ove t he cu rso r t o t h e
seco nd par t of M o d e an d
select th e Pro t o co l t o
Frsky D t hen yo u can
b i nd w it h N o vice- III
SWA
SWC
SWB
Prot ocol Selection
To Previous Page
Loading...
