Eachine NOVICE-II User Manual

NOVICE-II 1-2S Brushless Micro Drone
Connect the battery for the NOVICE-II
3 Star t FPV Flight
Start by powering on your Radio and Goggles. NOVICE-II comes already bound
to your radio and on the right video channel matched with your goggles. Power
on NOVICE-II by sliding the battery into the battery tray and plugging it in. Once
the battery is plugged in, set NOVICE-II on a stable surface so it can calibrate.
Calibration takes a few seconds then NOVICE-II is ready to fly.
Install 4x AA 1.5v battery to the radio and push the power switch to turn on
the radio. If the throttle stick was not at the bottom position the radioter will
alarm.
1
. Turn on the Vr009 goggles and check the Video
Toggle SWA(AUX1) switch to arm the NOVICE-II , you will find "ARMED" notice
in the screen of the Goggles. Recommend Toggle SWC(AUX2) to choose Stable
mode for the beginner. Happy flight and keep it safe.
4
-1-
Brand Name: Eachine
Item Name: NOVICE-II 1-2S Toothpick RTF & Fly more
Wheelbase: 120mm
Size: 100mm*100mm*40mm
Weight: 50g(without battery)
1 Specification
2 Features
Nano X F4 pro flight controller
Powerful and smoothly
Led Strip ready
Built-in Buzzer
New design 1103 KV8500 motors
Camera Angle adjustable
VTX power switchable 25mw~200mw
Smartaudio ready , change VTX bands, powers, channels via OSD
Ready to fly
Compatible both for 1s-2s Lipo/LIHV
3
Power with 1S batteryPower with 1S batteryPower with 1S battery
Power with 2S batteryPower with 2S batteryPower with 2S battery
2
120
99
43
NC1201
NC1203
NC1205
NC1204
NC1209
NC1208
NC1210
NC1211
NC1212
NC1207
NC1206
NC1206
Item
RTF
Par t No. FLY Mor e
NC1210
NC1204
NC1205
NC1206
NC1207
NC1203
NC1212
NC1201
NC1208
NC1209
NC1211
120mm toothpick frame
NanoX F4FS V1.0 flight controller
Eachine NC1103 KV8500
HQPROP T65 bi-blade propeller
Caddx EOS2 v2 version 4:3
VTX: 5.8g 25mw~200mw switchable Whoop VTX
3.8v 460mah battery
6in1 6-way LIPO/LIHV Charger
FS-I6 2.4G radio transmitter
Eachine VR009 5.8G 40CH goggles
Propeller disassemble tool
Screwdriver
LED&Buzzer PCB top board
M2*D3.5*L20 Aluminum Alloy column
Damping ball
Batter y mounted tray
1
1
4
2
1
1
2
1
1
1
1
1
1
4
4
2
1
1
4
2
1
1
10
1
1
1
1
1
1
4
4
2

Eachine NOVICE-II Specifications

General

Brand	Eachine
Model	NOVICE-II
Category	Drones
Language	English

Summary

Start FPV Flight and Setup

Install Radio Transmitter Batteries

Install AA batteries into the radio transmitter and power it on.

Power on the NOVICE-II Drone

Connect the battery to the NOVICE-II and place it on a stable surface for calibration.

Prepare FPV Goggles

Turn on the FPV goggles and verify the video feed.

Arm Drone and Select Flight Mode

Use transmitter switches to arm the drone and choose flight modes.

Flight Controls and Stick Operations

Left Stick Controls

Diagram illustrating left stick functions for throttle and yaw.

Right Stick Controls

Diagram illustrating right stick functions for pitch and roll.

Lipo Battery Charging

Flight Controller Connection Diagram

Radio Transmitter Binding Procedure

Receiver and VTX Configuration

Receiver Configuration Setup

Configure receiver mode in Betaflight Configurator for SPI RX support.

VTX Channel Settings

Setup VTX bands and channels for video transmission.

Goggles and VTX Channel Matching

Set up FPV goggles and VTX receiver channels.

Mixer Type and ESC Protocol

Configure mixer type and ESC/motor protocol.

PID and Current Settings

Default PID settings and current configuration.

Radio Channel and Mode Settings

AUX Channel Setup

Configure auxiliary channels for switches on the transmitter.

LED Strip Configuration

Configure LED strip functions and colors.

ESC and Firmware Management

ESC Check and Firmware Flash

Check ESCs and flash firmware using BLHeliSuite.

Flight Controller Firmware Update

Update the flight controller firmware using Betaflight Configurator.