This document provides installation and usage instructions for the EAGO AM505ETL TS-series Control Panel, a component of a massage bathtub system.
Function Description
The AM505ETL TS-series Control Panel serves as the central interface for operating various functions of the massage bathtub. It allows users to control water jets, adjust water temperature, manage audio features (radio and Bluetooth), and activate an ozone cleaning function.
Key functions include:
- Jet Strength and Mode Control: Adjust the intensity and pattern of the water jets for a customized massage experience.
- Heater Control: Turn the heater on/off and set the desired water temperature (range: 30°C-45°C). The heater operates only when the surfing water pump is active.
- Audio System:
- Radio: Turn on/off, scan for stations, adjust frequency (87.5MHz-108.00MHz), and control volume.
- Bluetooth: Connect to external devices for music playback, control play/pause, skip tracks, and adjust volume.
- Ozone Cleaning: Activate the ozone function for sterilization, which automatically turns off after 10 minutes.
- Light Control: Change the color of the bathtub lights.
- Child Lock: Lock the control panel to prevent accidental operation.
- Water Level Detection: The system requires the water level to be higher than the water level probe for certain functions (e.g., water pump, jet mode) to operate.
The faucet switch diagram illustrates how to control water flow and temperature:
- Two sets of faucets: One for the shower head (left turn for cleaning, right turn for shower head) and one for hot/cold water mixing.
- Three sets of faucets: One for the shower head, one for hot/cold water mixing, and one for the hand-held faucet.
Important Technical Specifications
The electrical control system box has the following parameters:
- Rated voltage: AC220V-240V / AC110V-120V
- Rated frequency: 50HZ / 60HZ
- Standby Power: <10W (All load is closed)
- Ambient temperature: +5°C - +40°C
Devices controlled by the system:
- Surfing water pump: 2HP
- Electromagnetism valve: 4-DC12V/5W
- Heater: 1500W
- Ozone generator: DC12V/6W
- Bottom light: DC12V/1W
- Speaker: 8Ω/5W (Maximum)
Power parameters for specific components:
- Rated power: 1120W
- Water pump:
- Rated voltage: AC220V/240V (50HZ), AC110V/120V (60HZ)
- Rated current: 5A
- Power: 1500W
- Ozone generator:
- Rated voltage: DC12V
- Rated current: 0.5A
- Power: 6W
- Bottom light:
- Rated voltage: DC12V
- Rated current: 0.5A
- Power: 6W
Installation conditions:
- Water pressure: 0.15~0.40MPa
- Ground support: The ground must be able to support the estimated load.
- Overflow: Water level should not exceed the overflow level.
- Drainage pipe: Diameter of water drainage outlet is 38mm.
- Ground wire: Minimum size copper wire of ground wire must not be less than 1.5mm². Yellow & green wire of water pump are ground wires, diameter 8mm.
Usage Features
The control panel features a user-friendly interface with touch controls and an LCD display for feedback.
Control Panel Operation:
- On/Off: Press the power button for 2 seconds to turn the system on/off. The system automatically turns off after 60 minutes if no operation is detected.
- Jet Control:
- "Jet Strength" button: Adjusts jet intensity (three levels).
- "Jet Mode" button: Cycles through different jet modes (e.g., continuous, interval, pulsating).
- Heater Operation: The heater automatically maintains the set temperature. If the water level is insufficient, the heater will not operate.
- Radio Operation:
- "Radio" button: Turns radio on/off.
- "FM/AM" button: Switches between FM and AM bands.
- "Frequency increase/decrease" buttons: Adjusts radio frequency in 0.1MHz steps.
- "Volume adjustment" buttons: Adjusts radio volume (range 0-20).
- "Channel picking out" buttons: Selects saved channels.
- Bluetooth Operation:
- "Bluetooth" button: Turns Bluetooth on/off, connects/disconnects devices, and searches for new devices.
- "Play/Pause" button: Controls music playback.
- "Previous/Next" buttons: Skips tracks.
- "Volume adjustment" buttons: Adjusts Bluetooth audio volume.
- Light Control: "Light" button cycles through different light colors.
- Ozone Function: "AUX" button activates ozone cleaning.
Safety Information:
- Always read and follow instructions.
- Ensure a qualified earth leakage circuit-breaker is installed and tested.
- Electrical wiring replacement must be done by a qualified engineer or retailer.
- Ground wire for pumps must be properly connected (minimum 1.5mm² copper wire).
- Do not remodel, add, or remove parts.
- Avoid using the product under the influence of alcohol or drugs.
- Children must be supervised.
- Keep electrical spare parts stable to avoid slipping into the tub.
- Mixed water temperature should not exceed 60°C.
- Do not use strong corrosive chemicals for cleaning.
- Avoid touching the water pump when running as it can be hot.
- Water level must be higher than the jet before operation.
- Do not drop anything into the water pump or opening holes.
- Connect to a GFCI/RCD socket.
- Do not use extension cords.
- Do not grasp the hand wheel drainer, nozzles, piping, or handrails during unpacking to avoid damage.
Maintenance Features
The manual provides clear instructions for maintaining the bathtub's surfaces and components.
1. Clean the acrylic surface:
- Use cotton flannel or sponge with water for daily cleaning.
- For scratches, use No. 1500 water abrasive cloth to polish lightly, then polish with toothpaste and cotton flannel.
- Avoid strong caustic chemical liquids like sulphuric acid, hydrochloric acid, or lye.
2. Plated item maintenance:
- Clean with cotton flannel.
- Do not use coarse cloth.
3. Suction net cleaning:
- Unscrew and remove the suction net to clean dirt, ensuring smooth water flow.
- Avoid strong caustic chemical liquids for cleaning.
Troubleshooting Guide:
The manual includes a detailed troubleshooting section for common issues:
- Bathtub shaking/loud noise: Check for imbalance, loose nuts, or motor issues.
- Motor runs but no water spray: Check for blocked backwater net, low water level, hydraulic governor, or air in the pump.
- Massage motor/air pump not working: Check for abnormal voltage, power connection, blown fuse, tripped switch, no display on control panel, no water level probe signal, or broken baroswitch.
- Chromatic lamp off: Check plug and control circuit panel.
- Insufficient water flow: Check water pressure and inlet pipe blockage.
- Shunt valve failure: Replace broken rubber gasket.
- No air from massage nozzle: Check for stuck air pipe, air pump off, or air pump malfunction.
- Water exhaust device doesn't bounce or leak: Check for loose screws, broken zipper, or uneven rubber gasket.
Maintenance Record and Service Card:
The document includes pages for recording maintenance activities and a service card with warranty information.
- Warranty Period: One year from the purchase date.
- Exclusions: Damage due to inappropriate usage, maintenance by unauthorized personnel, lack of proof of purchase, altered documents, or force majeure/natural disaster.
- Repair Costs: Free for quality-related damages within warranty; otherwise, costs apply.
Need help?
To Next Page
General