EAGTAC D25A User Manual

Instruction Manual
D25 models
EAGTAC
High Performance Tactical Flashlights
http://www.eagletac.com
D25 clicky - Quick Specications
“No Hassle” EagleTac Warranty
For repair, replacement, or other inquiries
contact your EagleTac dealer. You can also
reach our customer support via email at
support@eagletac.com.
We warrant our ashlights to be free from
defects in workmanship and materials. We
will repair, replace at our option, without
charging any product or part which is
found to be defective under normal use
within 120 months from the date of
purchase with the proof of purchase.
Electronics, chargers and rechargeable
batteries are covered for a period of 12
months with purchase receipt. Such repair
or replacement shall be the purchaser’s
sole and exclusive remedy under this
warranty. Normal wear and tear including
batteries draining is not covered, nor is
damage resulting from modication,
misuse, abuse, neglect, battery leakage,
improper maintenance or repaired by
anyone other than EagleTac.
D25A D25A2
MAX O.T.F. lumen
Runtime
Battery Types
Voltage
D25C D25C2/D25LC2
*Out-the-front lumen for CREE XP-G S2 / CREE XM-L U2 respectively
**(P25A/P25C) When using single protected 3.7V rechargeable li-ion,
medium brightness level will become turbo output. ***D25LC2 only
MAX O.T.F. lumen
Runtime
Battery Types
Voltage
110/122*
1.3 - 150 hrs
1xAA
0.9V-1.5V & li-ion**
219/277*
0.9 -150+ hrs
1xCR123A
1.8V-3.2V & li-ion**
343/548*
1 - 100+ hrs
2xCR123A/18650
***
2.7V-9V
220/278*
1.4 - 200+ hrs
2xAA
1.8V-3.2V
series - ClickyD
WARNING - All batteries (especially
lithium and Li-ion cells) can explode
or cause burns if disassembled,
shorted, or exposed to high tempera-
ture. Do not mix new and used cells
or dierent battery types/voltage, or
install battery backwards.
EagleTac ashlights use “button-top”
battery (battery with protruding posi-
tive). For rechargeable li-ion battery,
use only EagleTac li-ion battery to
ensure safety, high performance, and
good battery tment. Always ensure
the battery outer wrapping is com-
plete to prevent short circuit. When
the light output starts to dim, replace
batteries and do not drain the batter-
ies completely, especially when using
two (or more) batteries setup.
Battery Safety Precaution
WARNING - Some NiMH rechargeable
cells may release gas during
discharge. If you experienced high
pressure being built inside the light,
switch o the ashlight immediately
and release the pressure gently.
Replace batteries if necessary.
Caution when using Li-ion in D25A & C
Using 3.7V li-ion direct drives the LED
at maximum current level. Limit each
usage to less than ve minutes (or less
than one minute each with freshly
charged li-ion for the rst couple
times). Hold the light in your palm to
help removing heat from the LED
faster. If you nd the ashlight too
warm to hold, turn o the light to
allow the light to cool down. Do not
leave the light running unintended.

EAGTAC D25A Specifications

General

Battery Type	1xAA
Battery	1xAA
Waterproof	IPX-8
Impact Resistance	1 meter
LED Type	Cree XP-G2
LED	Cree XP-G2
Material	Aircraft-grade aluminum
Modes	High, Medium, Low
Runtime (Low)	150 hours

Summary

EagleTac Warranty Policy

Warranty Coverage Details

Covers defects in workmanship and materials for 120 months. Electronics, chargers, batteries for 12 months.

Warranty Exclusions

Excludes normal wear, damage from modification, misuse, abuse, neglect, or improper maintenance.

EagleTac D25 Models Instruction Manual

D25 Clicky Quick Specifications

Provides detailed specifications for D25A, D25C, D25A2, D25C2, and D25LC2 models.

Li-ion Battery Usage Caution

Limit Li-ion usage to under five minutes; hold light to dissipate heat. Turn off if too warm.

Battery Safety Precautions

General warnings for all batteries, including explosion risks and proper handling.

NiMH Battery Gas Release Warning

NiMH cells may release gas; release pressure gently and replace if necessary.

Battery Type and Handling Recommendations

Use button-top batteries. Ensure li-ion wrapping is complete to prevent shorts. Replace when dim.

D25 Clicky Series Quick Start Guide

Battery Installation

Unscrew tailcap, insert batteries with positive terminals facing front, tighten snugly.

Basic Operation Instructions

Click switch to turn on/off. Toggle light output by slightly pressing switch within 1.5s.

Mode Switching via Head Tightness

Tighten head for Group 2 (Turbo, Strobe); loosen for Group 1 (Low, Med, High, SOS).

Mode Switching via Switch Press

Slightly press and release switch (within 1.5s) to cycle through outputs in the current group.

Programmable Features

Adjust moonlight output and enable/disable mode memory for Group 1 settings.

Carrying Method and Clip Orientation

Use pocket clip for secure carrying. Reverse body to change clip orientation.

Maintenance Recommendations

Clean threads/o-rings, lubricate. Dry after moisture exposure. Do not clean reflector.