The EASTBROOK LED CEILING FAN, model #EST52MBK5LR, is a ceiling-mounted fan designed to provide air circulation and illumination. It features a remote control for convenient operation and is suitable for various room sizes and ceiling heights, with specific mounting options for standard, angled, or closemount installations.
Function Description
The primary function of this device is to circulate air within a room and provide lighting. It operates with a remote control, allowing users to adjust fan speed and light settings from a distance. The fan offers multiple speed settings (high, medium, low, off) and light control (on, off, dimming). It also includes a reverse switch to change the direction of blade rotation, enabling seasonal use: downward airflow for cooling in warmer weather and upward airflow to circulate warm air in cooler weather.
Important Technical Specifications
- Model Number: EST52MBK5LR
- Electrical Rating: 120V / 60 Hz
- Motor Amps: 1.25 MAX
- Bulb Type: Uses three standard-base 6.5-watt LED bulbs or CFL/incandescent equivalent.
- Blade Clearance: Blades must be at least 7 ft. above the floor and 30 inches from any obstruction.
- Ceiling Angle: For angled mounting, the ceiling angle must not be steeper than 20°.
- Remote Control: Not for use with solid state fans.
- Estimated Assembly Time: 120 minutes.
- Weight: The fan is designed to be supported by an outlet box rated for fan support, with a maximum weight of 35 lbs (15.87 kg).
Usage Features
- Mounting Options:
- Downrod Mount: Best suited for ceilings 8 ft. or higher, or for angled/vaulted ceilings (up to 20°). A longer downrod (not included) may be necessary for proper blade clearance on taller or angled ceilings.
- Closemount: Suitable for ceilings lower than 8 ft. high.
- Remote Control Operation:
- Power: ON/OFF button to turn the fan and light on/off.
- Fan Speed: Buttons for HIGH, MEDIUM, LOW, and OFF fan speeds.
- Light Control: Light ON/OFF button. Pressing and holding the light button for approximately 0.7 seconds activates the dimming function, cycling through brightness levels. The light has an auto resume function, retaining the last brightness setting.
- Learning Process: If the fan or remote control fails to operate, a new remote control can be paired by restoring electrical power, then pressing and holding the ON/OFF button on the remote for 5 seconds until the fan beeps.
- Reverse Switch: A manual reverse switch located on the light kit fitter (I) allows the user to change the direction of blade rotation for seasonal comfort. In warmer weather, the switch should be set to the LEFT position for downward airflow. In cooler weather, it should be set to the RIGHT position for upward airflow. The switch must be set completely LEFT or completely RIGHT; if it is in the middle position, the fan will not operate.
- Safety Precautions:
- Always disconnect power at the circuit breaker and wall switch before installation or maintenance.
- Ensure the outlet box is properly grounded.
- Do not bend blade arms during installation, balancing, or cleaning.
- Do not insert objects between rotating fan blades.
- Use only parts provided with the fan to avoid voiding the warranty.
- Ensure all screws, bolts, and nuts on the fan motor assembly are secured after installation.
- Avoid using a full range dimmer switch (not included) to control fan speed, as this can cause a loud humming noise.
- The remote control receiver is not compatible with solid state fans.
- Battery for the remote control is not rechargeable; remove battery when low or not in use for extended periods. Dispose of batteries properly.
Maintenance Features
- Cleaning: At least twice a year, check the canopy (F) to ensure downrod (C) assembly and all screws on the fan are tight. Clean the motor housing (H) with a soft brush or lint-free cloth to avoid scratching the finish. Clean blades (K) with a lint-free cloth. Occasionally, apply a light coat of furniture polish to wood blades (K) for added protection.
- Bulb Replacement: Use three standard-base 6.5-watt LED bulbs or CFL/incandescent equivalent. Allow bulbs and shades to cool down before touching them.
- General Maintenance: Shut off main power supply before beginning any maintenance. Do not use water or a damp cloth to clean the ceiling fan.
- Troubleshooting: A comprehensive troubleshooting guide is provided to address common issues such as fan not moving, noisy operation, excessive wobbling, fan operating but lights failing, and remote control failure. Solutions range from checking power connections and tightening screws to replacing batteries or re-pairing the remote control. "Wobble" is considered normal and should not be considered a defect.
Package Contents (Key Components)
- Mounting Bracket (A)
- Canopy Mounting Screws/Lock Washers (B)
- Downrod (C)
- Pin (D) and Clip (E)
- Canopy (F)
- Remote Pack (G)
- Motor Housing (H)
- Light Kit Fitter (I)
- Bulbs (J)
- Blades (K)
- Remote Control Receiver (L)
- Blade Arms (M)
- Motor Screws/Lock Washers (N)
- Light Kit Fitter Screws (O)
- Shades (P)
- Socket Rings (Q)
Hardware Contents
- Blade Screws (AA)
- Fiber Blade Washers (BB)
- Wire Connectors (CC)
The EASTBROOK LED CEILING FAN is designed for ease of installation and long-term use, backed by a limited lifetime warranty covering the fan motor and a one-year warranty for other parts. Customer service is available for questions, problems, or missing parts.
To Next Page
Need help?
General